Search messages and discussions

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 11+: 60 results shown for Permatex.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

• Re: Oil Temp Sender and Gauge
  Historical mailing list - Bruce Todd
  Fri, 25 Jun 2021 15:36:07 -0700
  It was Permatex thread sealant - high temp. Doesn’t require much and give about 4 hrs min of drying time. The stuff works well...
• Re: intake gasket?
  Historical mailing list - Scott Daniel - Turbovans
  Sat, 12 Mar 2011 13:23:20 -0800
  ...Does the collected >>>wisdom here say replace it or use the old one? >>>Should I get some kind of high-temp Permatex to fill...
• Re: Problem with push rod tube seals?
  Historical mailing list - Scott - IMAP
  Mon, 27 Jun 2016 16:19:38 -0700
  ...I use my fav Permatex High Tack gasket sealer on both sides of the seals. I have stretched the tubes much too far a...
• Re: Effectiveness of cooling system flush and clean products?
  Historical mailing list - Scott Ohana
  Fri, 7 Jun 2013 15:49:30 -0700
  ...re-attach cooling hoses and fill with Gunk/Permatex > heavy duty radiator flush/cleaner 5. Run engine up to operating temp and > idle for...
• Re: Request for detailed install directions for rear heater core
  Historical mailing list - Eric Caron
  Wed, 10 Dec 2014 16:32:39 -0500
  ...If the new core doesn't come with an O-ring or gasket, use Permatex "Right Stuff" sparingly to get a good seal. >> >> The...
• Re: update: help needed can not drive van...oil seals for Syncro
  Historical mailing list - Jay lefstein
  Mon, 20 Sep 2010 08:12:31 -0700
  ...This special seal keeps the water out along with the fact that the transmission is sealed to the engine with permatex and there is...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - Dennis Haynes
  Sun, 20 Sep 2015 20:33:35 -0400
  ...Way mo' easy to get out next time. > > I strongly recommend Permatex High Tack gasket sealer on the threads > of all screws going back...
• Re: Summary: Re: How hard is it to remove exhaust?
  Historical mailing list - Claudio Cella
  Mon, 9 Sep 2002 20:30:13 -0700
  ...Be careful not > to cross-thread the die. > > --When putting it all back together, use a good quality anti-seize compound > (I use permatex...
• Re: Request for detailed install directions for rear heater core
  Historical mailing list - Jim Felder
  Wed, 10 Dec 2014 17:29:02 -0600
  ...If the new core doesn't > come with an O-ring or gasket, use Permatex "Right Stuff" sparingly to get > a good seal. > >> > >> The...
• Re: quick and dirty head swap-dennis' 2 cents.
  Historical mailing list - Stuart MacMillan
  Thu, 23 May 2013 09:13:38 -0700
  ...the "Right Stuff" there along with a bunch of other products. Permatex also sells a rubber gasket dressing, 85409. Don't bother with epoxies...
• Re: Water Pump Replacement
  Historical mailing list - Jim Felder
  Thu, 9 Jun 2011 10:50:43 -0500
  ...anti-seize compound.. > > > or ..this works super well, I put red Permatex High tach on the bolt > > > threads.. > > > it' sticks 'em there , like anti...
• Re: 1985 - Horn COntact ring on Steering WHeel
  Historical mailing list - Scott Daniel - Turbovans
  Tue, 15 Jan 2013 21:42:11 -0800
  ...they would be WD and Permatex High Tack gasket sealer . That's how vitally important WD is. One thing is guranteed about WD-40...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - John Rodgers
  Sun, 20 Sep 2015 20:21:55 -0500
  ...Way mo' easy to get out next time. > > > > I strongly recommend Permatex High Tack gasket sealer on the threads > > of all screws going back...
• Re: Cool Air-Cooled (long)
  Historical mailing list - G. Matthew Bulley
  Thu, 7 Feb 2002 08:22:30 -0500
  ...Use copper PermatexR between all the pieces of tin-ware to eliminate air leaks. 2. Make sure ALL of your tin-ware is present...
• Re: Engine repair or replacement?
  Historical mailing list - Jack R.
  Tue, 19 Aug 2008 20:22:49 -0400
  ...Use something like Permatex on the edge (though I am told this > wont > > work it might be temporary fix) > > > > 3. Remove the engine and...
• Re: Summary: Re: How hard is it to remove exhaust?
  Historical mailing list - Ben McCafferty
  Tue, 10 Sep 2002 07:42:54 -0600
  ...Be careful > not >> to cross-thread the die. >> >> --When putting it all back together, use a good quality anti-seize > compound >> (I use permatex...
• Re: Mystery oil leak on 2.1 please help with ideas
  Historical mailing list - Vanagon Man
  Tue, 1 Jun 2004 07:49:27 -0400
  ...red sealing nuts and its properly torqued. > I also used aviation permatex on both sides of the gasket behind the oil > pump and the...
• Re: Engine repair or replacement?
  Historical mailing list - Scott Daniel - Turbovans
  Tue, 19 Aug 2008 17:28:45 -0700
  ...Use something like Permatex on the edge (though I am told this wont > work it might be temporary fix) > > 3. Remove the engine and...
• Re: going down for the second time w/ the waterpump
  Historical mailing list - Frank Condelli
  Sun, 6 Mar 2005 06:12:50 EST
  ...Use a very light coating of Permatex Grey RTV Silicon Sealant for aluminium surfaces on the O-ring when installing the new pump. This...
• Re: heater fan whine
  Historical mailing list - Tom Hargrave
  Tue, 26 Jan 2010 23:18:14 -0600
  ...It would be Permatex High Tack gasket sealer, and wd-40. People freak sometimes when I say what I fix with wd-40, particularly...
• Re: Mechanics using customer supplied parts.. Was bars leaks
  Historical mailing list - Keith Hughes
  Thu, 17 Sep 2009 14:50:37 -0700
  ...I take a look at the nice clean carb with the Permatex oozing out of all the gasket mating surfaces and have to tell...
• Re: Friday water pump fun!
  Historical mailing list - Neil N
  Fri, 19 Feb 2016 17:46:22 -0800
  ...is low for each pump fastener so I should > be ok. Permatex was also deployed at pump gasket. > > Here's some trip pics. One...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - SDF ( aka ;jim lahey' - Scott )
  Sun, 20 Sep 2015 19:24:29 -1000
  ...Way mo' easy to get out next time. > > I strongly recommend Permatex High Tack gasket sealer on the > threads of all screws going back...
• Re: Is this normal? (1977 camper advice)
  Historical mailing list
  Sun, 28 Apr 1996 19:57:40 -0700
  ...drying glue." What should I use for this? I just use permatex - the blue or red stuff in the tube. >I have RMMW and...
• Re: Problem with push rod tube seals?
  Historical mailing list - den jolliffe
  Tue, 28 Jun 2016 02:17:09 +0000
  ...I use my fav Permatex High Tack gasket sealer on both sides of the seals. I have stretched the tubes much too far a...
• Re: Mystery oil leak on 2.1 please help with ideas
  Historical mailing list - Doug in Calif
  Tue, 1 Jun 2004 06:08:03 -0700
  ...red sealing nuts and its properly torqued. > I also used aviation permatex on both sides of the gasket behind the oil > pump and the...
• Re: Vanagon Head Leaking Around The Head Nut(S)
  Historical mailing list - J Stewart
  Mon, 14 Apr 2014 11:29:05 +0000
  Everything was pretty clean, I coated the stud threads with a light coating of Permatex Anti-Seize. I torqued the heads to 40 ft...
• Re: Vanagon Head Leaking Around The Head Nut(S)
  Historical mailing list - OlRivrRat
  Mon, 14 Apr 2014 10:45:37 -0600
  ...clean, I coated the stud threads with a light coating of Permatex Anti-Seize. I torqued the heads to 40 ft. lbs per Ken...
• Re: General engine bolt/nut sizes
  Historical mailing list - Mike
  Mon, 14 Feb 2011 16:50:40 -0500
  ...I've been re-using them 'backwards' for many years, just adding a bit of red Permatex or silicone under the washer. It shouldn...
• Re: Engine repair or replacement?
  Historical mailing list - Jake de Villiers
  Tue, 19 Aug 2008 17:33:22 -0700
  ...Use something like Permatex on the edge (though I am told this > > wont > > > work it might be temporary fix) > > > > > > 3. Remove the engine and...
• DaBoat 2-liter update - bad heads :(
  Historical mailing list - David Schwarze
  Sat, 4 Nov 1995 13:23:26 -0800 (PST)
  ...Following Tom Wilson's instructions, I installed the new bearings, camshaft, and crankshaft, then coated the case seam with permatex 3-H and put...
• Replaced final drive to AT seals in the 90MV (fingers crossed anyway)
  Historical mailing list - retro van
  Sat, 16 Sep 2006 23:32:28 -0700
  ...month old $40 paper gasket at final drive bottom cover with permatex "the right stuff". refilled final drive oil, 1.25L - started engine for...
• Re: Engine repair or replacement?
  Historical mailing list - Jim Felder
  Wed, 20 Aug 2008 12:35:22 -0500
  ...pein hammer New exhaust gaskets 2 head gasket sets Right Stuff Permatex sealant Yellow bolt head sealant (comes with your gasket set, keep it...
• Re: Summary: Re: How hard is it to remove exhaust?
  Historical mailing list - Claudio Cella
  Tue, 10 Sep 2002 22:03:48 -0700
  ...Be careful > > not > >> to cross-thread the die. > >> > >> --When putting it all back together, use a good quality anti-seize > > compound > >> (I use permatex...
• Re: Problem with push rod tube seals?
  Historical mailing list - Scott - IMAP
  Tue, 28 Jun 2016 11:57:38 -0700
  ...tubes before head is fully tightened down. > > I use my fav Permatex High Tack gasket sealer on both sides of the > seals. > > I have...
• Gerbil engine replacement, part IV
  Historical mailing list - Dieter Dworkin Muller
  Sat, 06 Jul 1996 23:42:20 -0600
  ...For now, there's goodly amount of permatex around the gasket, and stud nut is roughly finger-tight. If/when it comes apart, I...
• Re: exhaust bolts / studs... tips or tricks?
  Historical mailing list - Scott Daniel - Shazam
  Sun, 18 May 2008 12:05:34 -0700
  ...consider the best, though I'm sure an American brand like Permatex is fine. Matter of fact, ........i never Mickey mouse stuff - ever ! But...
• Re: Vanagon Head Leaking Around The Head Nut(S)
  Historical mailing list - kenneth wilford (Van-Again)
  Mon, 14 Apr 2014 10:14:11 -0400
  ...clean, I coated the stud threads with a light > coating of Permatex Anti-Seize. I torqued the heads to 40 ft. lbs per Ken...
• Re: Rebuilding Vanagon Electric Windows or How To Go Into Debt rebuild electric motor
  Historical mailing list - Mark Keller
  Fri, 29 Apr 2005 10:08:42 -0700
  ...To be safe you may want to coat the mating joint, after joining, with permatex or simialar sealant. Clean up both the motor and...
• Re: General engine bolt/nut sizes
  Historical mailing list - Dennis Haynes
  Tue, 15 Feb 2011 01:02:26 -0500
  ...I've been re-using them 'backwards' for many years, just adding a bit of red Permatex or silicone under the washer. It shouldn...
• Re: Engine repair or replacement?
  Historical mailing list - Jim Felder
  Wed, 20 Aug 2008 15:13:49 -0500
  ...Use something like Permatex on the edge (though I am told this >>> wont >>> work it might be temporary fix) >>> >>> 3. Remove the engine and...
• Re: Engine repair or replacement?
  Historical mailing list - Robert Stewart
  Wed, 20 Aug 2008 17:38:23 -0400
  ...Use something like Permatex on the edge (though I am told this >>>> wont >>>> work it might be temporary fix) >>>> >>>> 3. Remove the engine and...
• Re: Oil.. Where's it go?
  Historical mailing list - Neil N
  Wed, 18 Oct 2017 15:49:11 -0700
  ...I have seen other conversions with pinched-off tubes, stuffed rags, bolt with permatex ... argh. One listee commented about complete removal and replacement with...
• Re: Vanagon Ownership Misadventures
  Historical mailing list - SDF ( aka ;jim lahey' - Scott )
  Wed, 30 Mar 2016 12:55:43 -1000
  ...For that very thin gasket I use *spray* Permatex High Tack sealant. Works perfectly ..very even thin coat. Never had an issue with one...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - John Rodgers
  Mon, 21 Sep 2015 16:32:40 -0500
  ...Way mo' easy to get out next time. >>> >>> I strongly recommend Permatex High Tack gasket sealer on the threads of >>> all screws going back...
• Re: quick and dirty head swap-dennis' 2 cents.
  Historical mailing list - Dennis Haynes
  Wed, 22 May 2013 22:03:26 -0400
  ...the "Right Stuff" there along with a bunch of other products. Permatex also sells a rubber gasket dressing, 85409. Don't bother with epoxies...
• Re: Engine repair or replacement?
  Historical mailing list - Jack R.
  Tue, 19 Aug 2008 20:53:50 -0400
  ...Use something like Permatex on the edge (though I am told this > > wont > > > work it might be temporary fix) > > > > > > 3. Remove the engine and...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - SDF ( aka ;jim lahey' - Scott )
  Mon, 21 Sep 2015 11:39:21 -1000
  ...Way mo' easy to get out next time. >>>> >>>> I strongly recommend Permatex High Tack gasket sealer on the threads of >>>> all screws going back...
• Re: Oil.. Where's it go?
  Historical mailing list - Alistair Bell
  Wed, 18 Oct 2017 16:33:04 -0700
  ...This clamped PVC hose approach has functioned perfectly. > > I have seen other conversions with pinched-off tubes, stuffed rags, bolt > with > > permatex ... argh. > > > One...
• Re: Vanagon Head Leaking Around The Head Nut(S)
  Historical mailing list - Dennis Haynes
  Mon, 14 Apr 2014 19:48:20 -0400
  ...Vanagon Head Leaking Around The Head Nut(S) Everything was pretty clean, I coated the stud threads with a light coating of Permatex Anti...
• The Misadventures of Vanagon Stan. Long, Long
  Historical mailing list - Stan Wilder
  Wed, 19 Jun 2002 07:03:49 -0500
  ...I installed the gaskets, gluing both sides of the gaskets and taking a thirty-minute break to let the Permatex Silicone High Temperature Sealer...
• Re: General engine bolt/nut sizes
  Historical mailing list - Joe Luther
  Tue, 15 Feb 2011 09:16:50 -0500
  ...I've been re-using them 'backwards' for many years, just adding a bit of red Permatex or silicone under the washer. It shouldn...
• Re: Head treatment for pitting--flattening technique
  Historical mailing list - Robert Fisher
  Tue, 18 Jan 2005 14:37:28 -0800
  ...The beer guy's first attempt at stopping the head gasket leak involved a large tube of red permatex. It took me a couple...
• Re: Engine repair or replacement?
  Historical mailing list - Ryan
  Wed, 20 Aug 2008 05:50:31 -0400
  ...Use something like Permatex on the edge (though I am told this >> > wont >> > > work it might be temporary fix) >> > > >> > > 3. Remove the engine and...
• Re: Engine repair or replacement?
  Historical mailing list - Jake de Villiers
  Tue, 19 Aug 2008 21:01:28 -0700
  ...Use something like Permatex on the edge (though I am told this > > > wont > > > > work it might be temporary fix) > > > > > > > > 3. Remove the engine and...
• Re: Engine repair or replacement?
  Historical mailing list - Jake de Villiers
  Wed, 20 Aug 2008 08:19:25 -0700
  ...Use something like Permatex on the edge (though I am told this >>> > wont >>> > > work it might be temporary fix) >>> > > >>> > > 3. Remove the engine and...
• Re: Engine repair or replacement?
  Historical mailing list - Robert Stewart
  Wed, 20 Aug 2008 00:44:36 -0400
  ...Use something like Permatex on the edge (though I am told this >>>> wont >>>>> work it might be temporary fix) >>>>> >>>>> 3. Remove the engine and...
• Re: General engine bolt/nut sizes
  Historical mailing list - Mike
  Tue, 15 Feb 2011 18:42:36 -0500
  ...I've been re-using them 'backwards' for many years, just adding a bit of red Permatex or silicone under the washer. It shouldn...
• Re: Engine repair or replacement?
  Historical mailing list - Jake de Villiers
  Tue, 19 Aug 2008 22:38:09 -0700
  ...Use something like Permatex on the edge (though I am told this >>>>>> >>>>> wont >>>>> >>>>>> work it might be temporary fix) >>>>>> >>>>>> 3. Remove the engine and...
• Re: Coolant Drain - 2.1 L
  Historical mailing list - John Rodgers
  Tue, 22 Sep 2015 17:18:47 -0500
  ...Way mo' easy to get out next time. > > I strongly recommend Permatex High Tack gasket sealer on the threads of > all screws going back...