Search messages and discussions

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 11+: 60 results shown for Screwdriver.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

• Re: Toolkit
  Historical mailing list - Scarlett Semko
  Tue, 23 Nov 1999 21:26:19 -0500
  ...tools to bring on a trip? > > 3/8" metric socket set > screwdriver set (2 x flathead, 2 x philips) > needle nose pliers > adjustable wrench...
• Re: SA Grill removal (still wondering)
  Historical mailing list
  Tue, 16 Nov 1999 20:22:29 EST
  ...Simply took a screwdriver and spread the clips a bit to make them looser. Now it's much easier to remove the grill. >> you...
• turning of the O2 sensor light
  Historical mailing list
  Wed, 8 Nov 2000 11:08:31 EST
  ...I pushed it all the way in, using a small screwdriver. I heard a satisfying click, climbed into the driver's seat, turned on...
• Re: vanagon Tool Box
  Historical mailing list - Bob Stevens
  Thu, 29 Jan 2004 22:03:23 -0700
  ...Apart from screwdrivers, pliers and duct tape, what are some > handy tools/items I should have on hand in case of emergency? > > Frank >
• Re: OXS light on
  Historical mailing list - Mike Collum
  Mon, 10 Jul 2006 10:55:52 -0400
  ...There is a hole into which you can insert a Phillips screwdriver or equivalent to push the reset button. you don't even have...
• Re: Help !! stripped screw
  Historical mailing list - Sudhir Desai
  Wed, 27 May 1998 18:59:09 -0400
  ...then, take a flathead screwdriver that is the correct size, and get that stubborn screw out of there. my $.02 worth, good luck, Sudhir...
• Re: help! part needed
  Historical mailing list - William Maxian
  Mon, 30 Aug 1999 14:27:30 -0400
  ...It's > threaded with a nut on one end and has a slot for a small screwdriver > blade on the other. See Bentley 20...
• how to change AFM track?
  Historical mailing list - John McLean
  Fri, 29 Dec 2000 22:32:46 -0800
  ...When I did this on my AFM I could not find a Phillips head screwdriver that fit the screw heads properly. I would guess...
• Re: german vanagons accessories
  Historical mailing list
  Fri, 17 Aug 2001 09:57:29 EDT
  ...covers up the holes where you would normally put in your screwdrivers to remove the grille, I gave up on the idea of bringing...
• AW: German Auto Tools Distributor?
  Historical mailing list - Robert Keezer
  Sat, 26 Oct 2002 18:59:55 -0700
  ...I vaguely remember green handled screwdrivers and some other unique designs on their web site, but nothing more. Thanks a bunch. Tom Naylor ('85...
• Re: SA (South African) Grille advice
  Historical mailing list - Andrew Grebneff
  Tue, 5 Jun 2007 19:02:22 +1200
  ...concerned about breaking it. > > I found that I could insert a screwdriver shaft between upper and > lower > parts of those receptacles and gently pry...
• Baja trip, no headlights.....
  Historical mailing list - mark drillock
  Mon, 2 May 2011 20:48:08 -0700
  ...It was good and stuck, so I disconnected the battery ground side so I could safely pry it off with a screwdriver. Came off...
• Re: voltage converter needed. 12vt to 3vt
  Historical mailing list - David Beierl
  Sun, 8 Aug 2004 08:41:37 -0400
  ...good simple reliable way to run a 2.4 volt cordless >>screwdriver motor hard wired to the vanagon 12 vt system. >> >>The only thing...
• Re: Rings are stuck ...
  Historical mailing list - Jeff Schwaia
  Thu, 26 May 2011 19:51:43 -0700
  ...A small screwdriver in the ring gap should do the trick. Cheers, Jeff -----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com...
• Re: Engine Assembly Wizzdom
  Historical mailing list - Mike
  Sun, 29 Aug 2010 12:47:37 -0400
  ...The only time the case-split leaks is when some PO used a screwdriver to pry the case-halves apart. I've never had...
• Re: 65 pop-out window disassembly
  Historical mailing list
  Tue, 5 Mar 1996 22:24:43 -0500
  ...I like to use the screwdriver (reversable) that came in the original tool kit. once the window is out, remove the weatherstrip on the...
• Re: push rods
  Historical mailing list - Bradley Flubacher
  Sun, 18 Mar 2001 14:53:18 -0500
  ...After you've done it once, you can replace a tube in about 20 minutes with a wrench or two and one screwdriver. Brad...
• Re: Vanagon buyer's checklist......
  Historical mailing list - ian Butler
  Thu, 29 Aug 2002 09:35:30 -0400
  ...I can poke my right rear tire from inside with a screwdriver.. d'oh.. ian Butler / ian@hplx.net '87 Syncro GL, '88 Scirocco...
• removing cigarette lighter redux
  Historical mailing list - Woody Halsey
  Sat, 30 Sep 2006 11:42:44 -0400
  ...way or the other first? Do you need to use a screwdriver to pry it off? When I try simply to lift it off...
• Newbie test
  Historical mailing list - Hugh Solari
  Wed, 6 Feb 2008 17:37:39 -0500
  ...the propane!) I have plenty more questions, but I figured I'd start with one that doesn't require a screwdriver! Thanks All HS
• Re: Starter/relay/switch problem
  Historical mailing list - Jarrett Anthony Kupcinski
  Mon, 23 Jul 2012 11:07:49 -0500
  Screwdriver across the solenoid ignition wire and starter wire. Always hated doing that, though. I'd first suspect grounds. Not sure how things are...
• '81 Heater control cable question
  Historical mailing list - Tom Young
  Fri, 28 Nov 1997 15:48:59 -0800
  ...trim plate covering the levers off is to "ply with a screwdriver." Do I need to remove the instrument cluster to work on the...
• Re: Strange noise
  Historical mailing list - KBatzler
  Fri, 13 Nov 1998 06:56:35 -0800
  ...Mine did...but I pushed the sensor back into the sleeve, pulled it tight, held sleeve with screwdriver, and pushed sensor in tight. I...
• Re: Anti-sieze on 1987 Alloy lug nuts ?
  Historical mailing list - Jay & Kim Schmidt
  Sun, 21 Nov 1999 17:12:19 -0600
  I put never-seize on virtually every thread my wrench or screwdriver manipulates on my 77. Do this and in ten years when your...
• Re: radio support screw
  Historical mailing list - Jere & Beth Hawn
  Sun, 25 Feb 2001 23:15:27 -0800
  ...I used an offset screwdriver to get mine out, some what of a PITA. Option 2: Leave it outside unlocked down by Pike's...
• Re: side sliding windows
  Historical mailing list - Stan Harrison
  Tue, 19 Aug 2003 14:41:43 -0400
  ...Small short screwdriver from underneath, pressed up, while 1/4 turned with pliers many turns to release. (believe was slotted, but may have been...
• Re: Adjusting rear camber left side
  Historical mailing list - Stephen Grisanti
  Sun, 8 May 2022 15:11:30 -0400
  ...The mounting on the chassis is slotted and large screwdriver or lever is simply used to move the arm as needed after the bolt...
• Re: Manual Transmission Drive Flange Seal
  Historical mailing list - OlRivrRat
  Sun, 10 Aug 2014 13:12:05 -0600
  ...DriveFlangeSeals ~ It might be Helpful to have CirClip Pliers & > > a VeryLarge ScrewDriver(to Pry the OldSeal out) & a VeryLarge Socket(I think the one...
• Re: Oil pressure light and buzzer
  Historical mailing list - OlRivrRat
  Sat, 29 Jul 2017 23:08:21 -0600
  ...Vice grips turn the screwdriver. It breaks free -- HOORAY! > > Hmm spring is 60mm long. But how long should it be??? 60 mm sounds pretty...
• Re: Manual Transmission Drive Flange Seal
  Historical mailing list - Tom Young
  Sun, 10 Aug 2014 12:09:32 -0700
  ...DriveFlangeSeals ~ It might be Helpful to have CirClip Pliers & a VeryLarge ScrewDriver(to Pry the OldSeal out) & a VeryLarge Socket(I think the one...
• Re: Just some annoyances..
  Historical mailing list
  Thu, 14 Jul 2016 14:24:11 -0400
  ...pushthem out with a small flatbladed screwdriver from the side that you can see the two tips of the circlip. wear safety goggles and...
• Re: Adjusting Rear Camber
  Historical mailing list - Dave Mcneely
  Sat, 2 Jan 2010 18:42:24 -0500
  ...loosen the nut, pry the trailing > arm by inserting a big screwdriver in the slot, tighten the nut and > go. > > Assume here that I...
• Re: Paul's starter problems
  Historical mailing list - Thom Fitzpatrick
  Fri, 5 Apr 1996 10:47:34 -0800 (PST)
  ...s the best way to drive out the old starter bushing? Screwdriver and > hammer? I used an allenhead bolt. You might be able to...
• Re: tranny input shaft
  Historical mailing list - Chris S
  Sat, 22 Feb 2003 20:46:02 -0500
  ...A few good whack later the punch cut through the shell and I was able to pry out the bearing with a screwdriver. No...
• Re: careful removing drums! was drums scraping backing plate
  Historical mailing list - Al and Sue Brase
  Thu, 3 Mar 2005 18:59:36 -0600
  ...hit the drums from the back or used a pry bar/screwdriver, you most likely also bent the backing plates. If you hit the...
• Re: it's cold in MT and my van won't start re: belt tightening
  Historical mailing list - Scott Daniel - Turbovans
  Thu, 3 Nov 2011 21:13:48 -0700
  ...belt tightening > GET THE RIGHT BELT SIZE! > > with the proper 9.5 belt it can easily be adjusted with a 12" screwdriver. > I run...
• Re: Tool Kit for Vanagon
  Historical mailing list - Joel Walker
  Wed, 26 Jul 95 12:05:27 CDT
  ...semi-vanagon-specific tools??? - sears has a little Torx screwdriver set that is needed to remove the front vent windows. it's a screwdriver...
• Re: jack points on a 79
  Historical mailing list - Andy Gray
  Sat, 02 Mar 1996 21:29:52 GMT
  ...happy) Unless you hear otherwise, try judicious use of a Big Screwdriver, bodging bar, etc..... Check that jacking point itself hasn't *moved* - it...
• The spirit of the Type II lives!
  Historical mailing list
  Fri, 30 May 1997 14:44:17 -0400 (EDT)
  ...Reminded me of the many times I would crawl under my '71 van to short the solenoid terminals with a screwdriver to start it...
• Re: Transmission -- hard to get in first
  Historical mailing list - Per Lindgren
  Wed, 17 Nov 1999 01:08:16 +0100
  Matthew Pollard wrote: > > take two 13mm wrenches (box or open), channel locks or the sort, and a big > flat blade screwdriver and shimmy yourself...
• How to remove Vanagon battery?
  Historical mailing list - S.C. Harrison
  Mon, 24 Jun 2002 15:57:32 -0700
  ...Also tried using a pair of long flat-blade screwdrivers to ease it out. Also no luck. Such a simple task, and the manuals...
• Re: Is there a tool for safely taking apart headlight assemblies?
  Historical mailing list - Randy Bergum
  Thu, 9 Feb 2006 11:44:42 -0800
  ...I've taken them out with small > screwdriver's and needle nose pliers but looks like there is a specific tool > for these. Anybody...
• Check your fuel line hose clamps!
  Historical mailing list - Tabe Johnson
  Tue, 26 Aug 2008 21:10:54 -0700
  ...A half turn with the screwdriver solved the problem. So: Even if you're feeling good about having newer fuel lines, give the fittings...
• Re: PREPING FOR PAINT JOB ON 87 WESTY
  Historical mailing list - Eric Caron
  Sat, 7 Mar 2015 15:58:13 -0500
  ...First, >>> I cut a deeper slot > for the screwdriver. When using my big screwdriver, >>> part of the screw head broke off so I > carefully...
• Re: 1985 Windshield replacement
  Historical mailing list - Roger Sisler
  Thu, 27 Jan 2005 13:35:54 -0500
  ...screwdrivers and start in a corner.It is like removing a bicycle tire.Work the inner rubber lip with a few closley placed screwdrivers...
• Answers(was questions...)
  Historical mailing list
  15 May 96 21:23:00 +1900
  ...off the retaining bar with a screwdriver, and a little force and replace, use the same screwdriver, and force to replace. >2) Is it...
• Re: 91 GL won't start
  Historical mailing list - Michael Sullivan
  Sun, 20 Feb 2011 21:50:48 -0600
  ...not known good) switch and > tried to start it with a screwdriver. Same thing as the switch that's > in the car. Nothing at...
• Re: How To Install Coat Hooks
  Historical mailing list - Bill Kasper
  Fri, 25 May 2001 16:07:22 -0700
  ...side with the hole in it) pops out...work a small screwdriver up underneath the disc. there's a screw inside (i figured it...
• Re: Vent Window Removal
  Historical mailing list - Simon
  Wed, 17 Jul 2002 17:17:03 -0600
  ...The small, phillips-head chrome-and-black screwdrivers that come in a set of 6 in a small plastic case- you know the ones...
• Re: Headlight Switch
  Historical mailing list - David Beierl
  Fri, 18 Jan 2013 14:32:42 -0500
  ...I did it on their kitchen table with only their basic handyman tools (a screwdriver, I imagine). Yours, David
• Re: Source for black window seals w/o moulding groove
  Historical mailing list - Christopher Gronski
  Sun, 22 Jan 2006 07:17:21 -0500
  ...gronski@GMAIL.COM writes: > > > Basically you just work a couple of screwdrivers > around the inside seal, folding it back as you go. The window...
• Re: How do I remove these clamps???
  Historical mailing list - Mike
  Sun, 3 Jun 2007 21:21:41 -0400
  I always stick a pick, awl or small screwdriver in and wiggle it open. They can then be re-used by crimping them with...
• Re: changing pop-top canvas
  Historical mailing list - Bob Stevens
  Tue, 23 Dec 2008 18:39:36 +0000
  ...I used a Black/Decker small electric cordless screwdriver which has an end or handle that folds/bends so you can get it into...
• Re: ignition switch shenanigans
  Historical mailing list - Shawn Wright
  Mon, 20 Sep 2004 07:24:12 -0700
  ...After that, I resorted carrying a screwdriver in the driver door, turning the key on & shorting the starter terminals under the hood with the...
• Heater removal
  Historical mailing list - Gerald Skerbitz
  Mon, 20 Feb 1995 11:41:55 -0600 (CST)
  ...It zinged by me when I pried it off with a screwdriver and I have *no* idea where it went. Gerry (shaking head and...
• Replaced evil Temp2
  Historical mailing list - David Bohannan
  Thu, 24 Aug 2006 22:22:27 -0400
  ...old one came out real easy, clip came out with small screwdriver, then 19 mm wrench and a small amount of coolant... I'll...
• Re: Can Anyone Spare a Dometic LP gas orifice?
  Historical mailing list - Roger Sisler
  Sat, 10 May 2008 14:48:30 -0400
  ...Just turn the screw with a screwdriver bit turned backwards and the pressure will change. Maybe yours has loosened up and let the pressure...
• Re: Solenoid Fix (was: How to turn the van over from the back)
  Historical mailing list - Todd Last
  Wed, 13 Jun 2001 23:16:54 -0700
  ...work after you whack the solenoid with a small hammer or screwdriver. My Vanagon had this problem when I first got it - but strangely...
• Re: Detailed list of what size sockets/wrenches/tools do you carry??
  Historical mailing list - Jim Felder
  Wed, 31 Jan 2007 15:19:59 -0600
  ...Offset screwdriver for where a regular screwdriver won't fit, especially helpful for westy interior. This will all fit in a transparent plastic container...
• Re: westy water tank
  Historical mailing list - Stephen Davis
  Wed, 8 Jul 1998 10:04:14 -0700
  ...I use a small blade screwdriver and it seems to work. A question for all. I have to fill the tank very slowly or...