Skip to main content
Gerry | Vanagon
Checking account...
← vanagon.com home · Continue the discussion in the forum
VanagonEuroVan

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 13+: 60 results shown for Ignition switch.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: Archive question and ignition switch question (update)
    Historical mailing list - Ken Wilford
    Fri, 26 Oct 2007 17:21:18 -0400
    ...my archive search went poorly was that I used "ignition > switch" and not "ignition" It mentions using a qualifier but my page just > stopped...
  • Re: horn not working after replacing ignition switch?
    Historical mailing list - Scott Daniel - Shazam
    Fri, 21 Dec 2007 14:38:23 -0800
    ...horn not working after replacing ignition switch? I replaced the ignition swith in my '87 this summer (to attempt to fix a problem that...
  • Re: What does x mean on fuse/relay panel wiring diagrams?
    Historical mailing list - Karl M.
    Sun, 24 Sep 2000 19:42:41 -0400
    15 = switched power from the ignition switch 30 = always-on power from the battery x = switched power from the load reduction relay 31 = ground...
  • Re: quick question - running rough after 2 minutes
    Historical mailing list - George Goff
    Tue, 20 Sep 2005 20:27:28 EDT
    ...one place: "With the ignition switched off, disconnect oxygen sensor. The oxygen sensor must be disconnected with the ignition off in order to cancel...
  • FW: 1980 Westy ignition quits
    Historical mailing list - Bergey, Dennis
    Thu, 21 Aug 2003 05:44:06 -0700
    ...dual relay, coil, control unit for electronic ignition, jumped the coil directly from the battery, replaced ignition switch, headlight switch! (i was fishing) halogen...
  • Re: Ignition switch replacement: where is it in Bently?
    Historical mailing list - Jimmy Johnston
    Thu, 31 Oct 2013 07:48:40 -0400
    ...Gregory Smith <gfs@gregoryfsmith.com>wrote: > I want to replace my ignition switch and thought it prudent to look it > up in my Bently...
  • Ignition Switch
    Historical mailing list - Steve Elfelt
    Wed, 1 Sep 1999 05:44:34 -0400
    ...I *did* have to remove the steering wheel from the steering column to replace the ignition switch itself. If memory serves, it was necessary...
  • Re: replacing ignition switch
    Historical mailing list - Blake Heinlein
    Fri, 15 Jun 2001 17:27:05 -0400
    Opps! Sorry I rushed through and didn't read the email correctly. Blake Heinlein '84 Vanagon Sacramento, CA
  • Re: Accessing Terminal 50 on Ignition Switch
    Historical mailing list - Jfp w/2 WBXs
    Sun, 14 Nov 2004 13:49:47 +0000
    Hi Tim, There should be access under the black cover on the steering column. John
  • 24mm deep socket
    Historical mailing list - Damon Lowe
    Wed, 23 Aug 2006 22:28:10 -0500
    the 24mm deep socket is used to remove the steering wheel. http://carboncow.net/vanagon/projects/ignition_switch.htm
  • Re: Could hot starting problems be caused by a defective ignition swich?
    Historical mailing list - The Bus Depot
    Fri, 16 Dec 2005 11:28:54 -0500
    ...Since the early Bus, VW has always routed the starter solenoid's current through the ignition switch rather than using it as a trigger...
  • Fried ECU diode...
    Historical mailing list - Kevin Faison
    Tue, 25 Mar 2003 17:11:08 -0500
    ...However pin 1 is shorted to ground when the ignition switch is just in the on position. My question is should pin 1 be...
  • Re: FIXED Re: horn not working after replacing ignition switch?
    Historical mailing list - Scott Daniel - Shazam
    Fri, 21 Dec 2007 18:18:28 -0800
    ...horn not working after replacing ignition switch? I replaced the ignition swith in my '87 this summer (to attempt to fix a problem that...
  • Ignition Switch "Su" Power
    Historical mailing list - neil n
    Thu, 24 Jan 2013 18:37:47 -0800
    ...The "Su" position in the ignition switch is unused. If I can find the buzzer, I could measure the current draw and compare to...
  • Re: NVC (but VW) '95 Cabrio intermittent no start - no spark
    Historical mailing list - David Beierl
    Fri, 4 Sep 2009 14:49:26 -0400
    ...For a start, get a mechanic's starter switch and establish whether it's ignition or fuel. I'm guessing ignition, but... When testing...
  • Re: lighted switch needed
    Historical mailing list - Scott Daniel - Shazam
    Sat, 9 Feb 2008 12:02:16 -0800
    ...That way you can still have tunes with 'engine and ignition off' . And can't forget and leave it on when you leave the...
  • Re: Weird headlight problem
    Historical mailing list - Thomas D. Hanlon
    Fri, 8 Sep 2000 06:13:15 -0500
    ...I actually > think I had to turn the ignition switch off to reset the problem. > I tried tracing the electrical diagrams but didn't...
  • Re: Ignition Switch Replacement
    Historical mailing list
    Fri, 9 Aug 1996 15:15:36 -0400
    ...Dyen Fred D.) writes: >I wonder if anyone has replaced their ignition switch. I checked the >Bentley, but the informaqtion is somewhat vague: "to...
  • Re: Daytime Running Lights-91 Carat
    Historical mailing list
    Tue, 25 Feb 1997 20:11:08 -0800
    ...bypass the switch when the engine is running and the alternator is cranking out power. If you ever sat with the ignition on to...
  • Re: help, brights won't stay on
    Historical mailing list - Bob Stevens
    Sat, 20 Apr 2002 16:53:12 -0600
    ...I have actually jiggled the ignition switch and had the lights come on when they would not otherwise. Thanks to Frank Condelli, there is...
  • Re: 87Syncro,Headlights won't turn on
    Historical mailing list - STEVEN G WACKER
    Fri, 19 Sep 1997 08:55:16 -0700
    ...I thought it would be the ignition switch so I tried moving it a little to see if the lights would come on, didn...
  • Re: Electric problem in 2.1l
    Historical mailing list - Jerry
    Wed, 29 Jul 2009 18:07:44 -0500
    Check your Ignition switch. I had a problem with my 88 GL headlights not working. My problem was the Ignition switch. Hope this helps...
  • Re: 3 questions: starter/ignition switch/temp warning light
    Historical mailing list - lauterba
    Sat, 20 Sep 2003 00:05:02 -0400
    ...starter/ignition switch/temp warning light > 1. I just replaced starter motor on my 84 westy. Does a new bushing really go > in there...
  • Re: Headlight swtich diagnostics?
    Historical mailing list - Ken Wilford
    Mon, 22 Dec 2008 14:14:13 -0500
    ...with > ignition off + headlight switch on, three LEDs in the dashboard glow. > With engine running + headlight switch off - normal. Engine running > + headlight switch on...
  • Re: replacing lock cylinders + ignition switch (starter button on dash)
    Historical mailing list - Bob Stevens
    Thu, 24 Apr 2003 11:43:39 -0600
    "Where would be the best location on the dash?" ...the underside of the plastic steering column shroud...very near the ignition lock....and out...
  • Re: ignition switch removal 75-79
    Historical mailing list - Matthew Henricks
    Wed, 27 Mar 1996 07:41:45 -0800 (PST)
    ...folks, > Anyone have first hand knowledge on the removal of the ignition switch > on a 75-79 bus?? From looking at the Haynes manual...
  • Re: Replacing Starter on 85 Vanagon - Jackstands or Ramps ?-The bypass button.
    Historical mailing list - Jeff Palmer
    Wed, 20 Mar 2013 19:22:44 -0500
    ...He replaced the ignition switch also, which had a seam on the plastic housing that had spread open (how that would happen I do...
  • Re: Ignition switch question
    Historical mailing list - Jim Arnott
    Tue, 20 Jun 2023 21:21:56 -0700
    ...Stop, turn key and remove. >>> My radio stays on until I open my door. >>> Did my ignition switch organically grow a new feature? >
  • L-shaped circuit board behind speedo...
    Historical mailing list - Fitz-Randolph, Douglas
    Fri, 9 Aug 2002 11:47:59 -0400
    ...With the original, the oil pressure LED blinks with the ignition switched on, then goes out immediately when the engine starts. With the replacement...
  • Re: Ignition Switch Electrical Repair
    Historical mailing list - Joe in NH
    Mon, 29 Dec 2003 19:42:44 EST
    ...I just did this to change the ignition lock/switch in my Syncro. Email if you have any more questions. Good luck and happy...
  • Re: 1991 Vanagon Electrical Problem
    Historical mailing list - Kim Brennan
    Mon, 16 Dec 2002 12:20:30 -0500
    ...Remove the wire connector from your ignition switch. Check the X circuit coming out of your switch. It is probably going bad. New ignition...
  • NVC- 71 Bus wiring
    Historical mailing list - Jim Cochran
    Fri, 13 Nov 2009 19:22:22 -0800
    ...I lost the last ignition key I had for my 1971 VW van... I had already bypassed the starter part of the switch years...
  • Re: ign switch
    Historical mailing list - Bill Davidson
    Sat, 13 Jan 2001 08:27:29 -0800
    ...You can buy them from www.busdepot.com or from Ken Wilfey who also has instructions for changing the ignition switch at http://www...
  • Re: Ignition Switch Electrical Repair
    Historical mailing list - phil cain
    Mon, 29 Dec 2003 20:45:41 -0800
    Jeff, You just fried the electrical portion of the switch, It is plastic and easy to remove, don't pull the mechanical part of...
  • Re: Ignition Switch Installed - still no start
    Historical mailing list - Zoltan
    Sun, 30 Sep 2001 21:07:42 -0700
    ...Ignition Switch Installed - still no start > Arghh.. > > New starter, new ignition switch. Battery is charged. > still no start. > > anyone have any other advice? This...
  • Re: ECU and starting question
    Historical mailing list - David Kao
    Tue, 17 Jul 2007 14:08:20 -0700
    ...The wire that feeds power to the relay (which activates or deactivates the switch) is coming from the pin #4 of the transistor ignition...
  • Re: A Mystery
    Historical mailing list - Dennis Haynes
    Sun, 1 Sep 2013 01:47:10 -0400
    ...While cranking does the alternator warning light remain lighted and does the tach needle move? If not check the ignition switch. It may fail...
  • Re: Just a click on turning ignition key
    Historical mailing list - Benjamin Tan
    Mon, 28 Aug 2000 15:55:35 EDT
    ...Then I would wiggle the key a few times in the hope that the (probably) defective ignition switch contacts will make contact. After this...
  • Archive question and ignition switch question
    Historical mailing list - TJ Hemrick
    Fri, 26 Oct 2007 15:46:19 -0400
    All, I was looking for info on changing my ignition switch (the electrical part not the whole assy) so like a good little boy...
  • Re: Ignition problem now worse
    Historical mailing list - Jim Morgan
    Tue, 30 Jan 2007 22:14:10 EST
    ...It make me suspect the throtle position switch. I was cleaning the throtle body with carb cleaner. It ate my switch. the van would...
  • Re: Is it the ignition switch, or something else?
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 29 Jan 2012 11:37:48 -0800
    ...The ignition lock > has a "tail" on it which engages the electrical switch and turns the > switch > to the various positions. If that "tail...
  • Re: Broken down, need some advise
    Historical mailing list - Raimund Feussner
    Sun, 13 Nov 2016 17:02:02 +0100
    ...It seemed like the battery > still had juice, so I suspected the ignition switch. I just tested jumping > the big red wire to the...
  • Re: Replace your ignition switch.
    Historical mailing list - David Marshall
    Mon, 7 Sep 2009 08:54:24 -0700
    I've done a few switches too - why why why did VW put current through the key and headlights?� A relay for the 15...
  • Re: Wiper Failure (again) X-switch for ignition
    Historical mailing list - John C...
    Sun, 6 Mar 2011 09:19:52 -0700
    On Sun, Mar 6, 2011 at 6:42 AM, mark drillock <mdrillock@cox.net> wrote: > The part of the ignition switch that burns out...
  • Re: Steering. Re: P 48.14 Measurement "a"
    Historical mailing list - David Beierl
    Sun, 3 Feb 2013 01:48:06 -0500
    ...and black plastic sleeve, >sprayed lube between ignition switch housing and tube, *lightly* >tapped the ignition switch housing toward driver. It, and inner rod...
  • ignition troubles
    Historical mailing list - Mervyn Readman
    Mon, 15 Oct 2007 20:41:35 -0400
    ...I am guessing the only cure is a new ignition switch. Anyone have any thoughts. I replaced the ignition a few years back for...
  • Re: no wipers, no blower motor, no headlights, no radio, no idea...
    Historical mailing list - Andrew Philbrick
    Fri, 27 Sep 2013 09:40:29 -0500
    ...Then I saw this thread and replaced the ignition switch. No change. Is there anything else to investigate? I've looked under the dash...
  • Re: Starter solenoid wiring question - '86 AT
    Historical mailing list - Ed McLean
    Wed, 1 Jun 2016 15:36:10 -0400
    ...Yes, the ST +12vdc passes through the safety switch in the AT console, not directly from the ignition switch ST terminal. Thanks, Scott, for...
  • Re: Digitool Just in Time
    Historical mailing list - Bulley-Hewlett & Associates
    Thu, 5 Nov 1998 20:58:46 -0500
    ...The fuel pump has two contacts in the ignition switch, the "start" one is okay, the "run" one is in Heaven, with Jesus and...
  • Re: Headlight relay setup not working in 89 Westy
    Historical mailing list - Don in Phoenix
    Thu, 6 May 2004 18:53:42 -0700
    ...are the ones coming from the Headlight Dimmer/Flasher switch, NOT the Ignition switch (the other side of the steering column). Those are from...
  • Re: Voltage leak found
    Historical mailing list - sailingfc dslextreme.com
    Tue, 1 Sep 2015 19:49:16 -0400
    ...Voltage leak found Since Vanagons don't have an Accessory position on their ignition switch, since many radios draw some current when off, since...
  • Re: Ignition/starter switch failures
    Historical mailing list - Jim Felder
    Tue, 12 May 2015 23:21:52 +0000
    ...net> wrote: > Over the last year I have had 3 ignition/starter switch (111 905 865L) > failures after not having but 3 failures in...
  • Re: 1980 Vanagon Ignition (accessory position)
    Historical mailing list
    Thu, 2 May 1996 23:33:40 -0400
    ...You now have an accessory position on your ignition switch by just inserting the key. If you can't find the buzzer relay, look...
  • Re: Poptop Alarm was Re: ebay car?
    Historical mailing list - Jay L Snyder
    Thu, 14 Feb 2002 10:56:37 -0500
    ...A relay could be used in line with the ignition switch and run to the limit switch. When the key is turned and the...
  • Re: Ignition/starter switch failures
    Historical mailing list - Old Volks Home
    Wed, 13 May 2015 00:22:35 -0700
    ...net> wrote: > Over the last year I have had 3 ignition/starter switch (111 905 865L) > failures after not having but 3 failures in...
  • Wiring Problem - Air Cooled Porsche
    Historical mailing list - Bill Minor
    Wed, 11 Sep 2002 09:37:10 -0500
    ...They got as far as unplugging the entire ignition switch so I'm sitting here with no wiring diagram and either a five hour...
  • Re: headlight emergency!
    Historical mailing list - Per Lindgren
    Mon, 6 Sep 1999 19:30:52 +0200
    ...Daniel, If that doesn't help, go for the ignition switch! The two most common failures when the lights disappear. PerL 87 Syncro 112i
  • Re: '86 Westy cranking trouble
    Historical mailing list - Jake de Villiers
    Sat, 19 Apr 2008 22:16:09 -0700
    ...A failed ignition switch is the > > kind of think that can stop a nice trip dead in its' tracks! > > > > Dan did you replace it...
  • Re: How to turn the van over from the back?
    Historical mailing list - David Beierl
    Mon, 11 Jun 2001 17:56:43 -0400
    ...how do >i switch it on from the back? extend all the wires at the ignition switch? You can get (or build) a mechanic...
  • Re: was fav 12 V acc, now 2nd battery relay system
    Historical mailing list - Robert Keezer
    Wed, 21 Feb 2007 13:10:11 -0800
    ...or you can wire to the > ignition switch so that paralleling the > batteries when starting is > automatic. > > Either way, you'll need to use...