

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 16+: 60 results shown for Idle Stabilizer.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Re: Wiring on power steering pumpHistorical mailing list - Shawn Wright, IS ManagerMon, 10 Feb 1997 20:14:29 -0800...Bentley shows (page 97.125) both wires coming from the Idle Stabilizer Control Unit, which I think is in the pass side area where...
- Re: 85 1.9, won't idle in trafficHistorical mailing list - MOST,DAVIDTue, 15 Aug 2000 16:02:42 -0700...Though people told me it wouldn't fix the problem, I came across another '87 and borrowed its idle stabilizer valve. Upon installation, I...
- Re: Idle at 1900 rpmHistorical mailing listThu, 30 Nov 2000 08:32:08 EST...Finally it could be your idle stabilizer unit. I have these new for $25 each (for 1.9l Vanagons only). Hope this helps. Thanks...
- Re: 81 CA van, trouble setting the timing(automatic)Historical mailing list - Dennis HaynesSat, 3 May 2008 12:14:55 -0400The idle stabilizer on that engine works by advancing the ignition timing when the idle goes too low. It needs to be bypassed to...
- Re: Idle Air Valve from a JettaHistorical mailing list - Tom MillerWed, 11 Feb 2004 12:39:16 -0500I put my 92 Jetta 8v 1.8L idle stabilizer on my 89 Westy with no problems. Worked fine. TEMiller ----- Original Message ----- From: "EMZ...
- Looking for 2.1l engine complete in Florida areaHistorical mailing list - kenneth wilford (Van-Again)Tue, 7 Jan 2014 13:45:47 -0500I have a customer that needs a good, used 2.1l engine along with the wiring harness, ecu, distributor, idle stabilizer, idle air valve...
- Re: Idle control valve and very cold weather?Historical mailing list - Jake de VilliersTue, 8 Dec 2009 20:15:30 -0800WBX Idle Stabilizer is fine at any temp, 1.9 and 2.1 both - but you have a non-standard engine so... On Tue...
- Re: Stalling at stop lightsHistorical mailing list - Roger SislerMon, 25 Apr 2005 17:40:02 -0400While you have the idle stabilizer connected together, check your timing. I have found that timing that is off in the 1.9 can...
- Idle setting on '84 WasserBoxer (w DigiJet)Historical mailing list - Paul HendersonWed, 20 Aug 1997 11:43:02 -0500...The manual directs me to remove the idle stabilizer plugs, plug them together (done), then simply "adjust the idle". Could some kind soul tell...
- Re: Vanagons: How lumpy is your idle?Historical mailing listTue, 4 Jun 1996 09:51:22 -0500...I've checked the idle stabilizer and it seems to be working. I assumed that the idle was normal. Colin A Moran If you...
- '87 2.1 Starting ProblemsHistorical mailing list - Tom SalicosTue, 31 Dec 2002 05:16:05 -0800...Does this sound like an idle stabilizer problem? I can swap with my '87 if it's deemed to be a likely cause. Thanks...
- Testing some componentsHistorical mailing list - Marc PerdueSat, 11 Jan 2003 11:51:19 -0500...Regarding testing components that affect the idle: Idle stabilizer valve--Okay, it's buzzing and it's been cleaned. Is that a clear indicator...
- High Idle Solution!Historical mailing list - brad barcomTue, 5 Feb 2002 18:53:38 -0500...After ruling out the idle stabilizer valve, the idle stabilizer control unit, and the temp II sensor, I finally made my way to the...
- Re: '83 vanagon: shot control module?Historical mailing listMon, 22 Aug 94 15:05:27 EDT...a faulty idle stabilizer and a collapsed hose running from the aux. air regulator to the bellows. The latter so I am told will...
- Re: Idle update/More bullshit.Historical mailing list - George GoffWed, 22 Jan 2003 09:07:03 ESTSpeaking of Idle Stabilizer Control Valves, in a message dated 1/22/03 6:54:55 AM, RAlanen@AOL.COM writes: << Yes, absolutely yes...
- bad idle during warmupHistorical mailing list - Bradley FlubacherWed, 22 Nov 2000 08:04:54 -0500...Can anyone recommend one way or the other with definite knowledge? Or maybe it's something else? (The idle stabilizer?) I've check both...
- Re: Idle Stabilization parts Costs Just dropped....Historical mailing list - Max WellhouseThu, 24 Feb 2011 17:09:09 -0600...I find I > > apparently will need an idle stabilizer valve and the idle stabilizer > > control box that goes in front of the right hand...
- Re: Idle stablilizer system testingHistorical mailing list - walter bahmThu, 18 Jan 2001 12:16:38 -0800...varys it can cause the module > to > > > cycle the stabilizer > > > valve and upset the idle speed causing your > symptom. > > > Also make certain > > > there are...
- orphaned wire in driver's side of engine compartmentHistorical mailing list - Mark McCulleyFri, 14 Aug 1998 19:32:26 -0700...The wiring diagram in the Bentley manual indicates that this wire goes to the idle stabilizer control unit. Anybody know what the purpose of...
- Re: Idle Stabilizer System Delete. Cause Bog Off Idle?Historical mailing list - Neil NSat, 11 Apr 2015 15:59:31 -0700...http://vnc.thewpp.ca/stuff/bentley/ep0niks.ctech.ca/vw/eva2/FU01/ch6.3.3.html " If the idle stabilizer valve is diagnosed as...
- More on Hote/Warm StartHistorical mailing list - jhlauterbachFri, 23 Oct 1998 07:16:43 -0400...Last night replaced Digital Idle Stabilizer and cleaned contacts. In process found that connection on Temp II was loose as locking snap on connector...
- Subject: Re: Idle Stabilizer Valve - Later UPDATE: problem *NOT*Historical mailing list - Clint KoldaThu, 25 May 2006 06:18:23 -0700My idle switch clicks closed when the throttle is completely closed. I can not adjust it to open to the Bentley specs. The switch...
- Throttle body/idle stabilizer woes...Historical mailing list - Jesse and Monica JohnsonSun, 14 Sep 2003 18:05:08 -0400Hey Everyone, I am having two problems...first is...my idle stabilizer is not working...the valve itself has continuity between the terminals...but...
- WARM/HOT START PROBLEMHistorical mailing list - jhlauterbachWed, 21 Oct 1998 20:55:51 -0400...Until this new problem started, I was having problem with fast idle after warm-up and have idle stabilizer and aux.. air regulator on...
- Rough Idle HelpHistorical mailing list - Michael DiehrFri, 6 Aug 2004 13:18:39 -0700...New cap, rotor, plugs & wires New AFM (rebuilt) New Oxy sensor New DIS (digital idle stabilizer) Adjusted valves Cleaned/adjusted Aux Air Valve Fixed...
- No idle/odd running.Historical mailing list - Brendan SlevinTue, 9 Oct 2007 20:59:22 -0700...I didn't disturb the idle stabilizer. other than disconnecting the vac lines from the intake. It is all back toether correctly. It is...
- Re: IDLE STABILIZER ???Historical mailing list - Per LindgrenSat, 10 Oct 1998 11:41:34 -0700...02 PM -0500 10/9/98, KENWILFY@AOL.COM wrote: > >>The Idle Stabilizer is that little green box that is attached to the > driver...
- Air Flow SensorHistorical mailing listWed, 15 Feb 1995 19:15:28 -0500...The mechanic said that the computer and idle stabilizer were fine. Does anyone have a used air flow box for a 1986 and up...
- Re: Definitive test for Hall > ECU?Historical mailing list - Dennis HaynesTue, 30 Oct 2007 06:49:13 -0400...Free, too. > > Start by setting the timing, with the idle stabilizer bypassed, to 10* ATDC, > hoses attached, 950 rpm. You should be able to...
- Engine Dies updateHistorical mailing list - Stephen M CanappWed, 14 Feb 2001 10:29:04 -0500...Looks Like Joel Walkers advice on the idle stabilizer valve sticking was my problem, I'll still check out the other suggestions. Thanks Again...
- Re: Diagnosing Idle stabilizerHistorical mailing list - Larry and Avery JohnsonThu, 23 Jan 2003 17:30:47 -0500<<I wonder if there is a beefier power transistor that you could replace the BD438 with that would not be so prone to burning...
- Re: Idle StabilizerHistorical mailing list - George GoffWed, 22 Jan 2003 07:22:43 ESTIn a message dated 1/22/03 1:05:32 AM, dbeierl@ATTGLOBAL.NET writes: << Solder joints have very poor fatigue resistance, and an...
- idle stabalizer plugs neededHistorical mailing list - Greg MarshallThu, 28 Mar 2002 17:58:51 -0500...running so hot, and found that some PO had removed the idle stabilizer , plugs and all. I need a new one now, and I...
- Re: How to disconnect idle stablizer??Historical mailing list - John RodgersWed, 27 Sep 2000 15:01:14 -0500If you have an 86 or later van with the 2.1L engine, you can simply disconnect it right at the idle stabilizer which...
- Setting timing on '85Historical mailing list - Peter KroghFri, 28 Sep 2001 14:09:53 EDT...Pull idle stabilizer plugs and plug together Pull distributor vacume lines Clamp induction wire on spark plug lead (which one) Shine on pulley. What...
- where did that wire go?Historical mailing list - steve vitaleTue, 18 Apr 2006 13:54:19 -0400there's a brown wire with yellow connector that hangs right above the thermostat housing that i believe is called a "Idle Stabilizer Control...
- Re: Recall for Fuel tankHistorical mailing list - Todd LastFri, 11 Jun 1999 19:41:57 -0700...the gas tank on my '87 > > Syncro Weekender sending unit and idle stabilizer had a recall. So, check > > it out with your local dealer...
- Re: More AFM/ECU reverse engineering results comingHistorical mailing list - jonWed, 20 Dec 2006 18:23:12 -0800All of the vanagons I have seen have the ECU under the rear seat, and the idle stabilizer behind the tail light. No big...
- Looking for wiring harness for 2.1l and other used parts.Historical mailing listFri, 28 Jan 2000 15:54:57 EST...Wiring harness from a 2.1l engine Used idle air valve Used idle stabilizer unit (black box behind pass side tail light) Vanagon Owner...
- Re: Surging 1.9 VanagonHistorical mailing list - Greg PottsMon, 2 Oct 2006 08:37:11 -0400Hi Lyle, Does the surging occur at idle or partial throttle? If at Idle it's a problem with the idle stabilizer circuit. Possibly...
- Re: Idle Control WhatzitHistorical mailing list - Michael aka ECHOTue, 10 Apr 2001 12:03:55 -0700...Step one > for the CA emissions is to disconnect the idle control > stabilizer and plug the leads into each other. I look high > and...
- Re: can't find timing marksHistorical mailing list - Old Volks HomeFri, 11 Nov 2005 10:31:00 -0800...Be sure to disconnect the Idle Stabilizer and reconnect the plugs to properly set the timing (at idle of course). When the timing is...
- Re: Idle Stabilization parts CostsHistorical mailing list - Scott Daniel - TurbovansThu, 24 Feb 2011 13:00:46 -0800...It uses the stock fuel rail but replaces the AFM, ECU, Idle > stabilizer, etc with a modern hot-wire fuel injection setup. > > For $600...
- Live nude ISCUs!Historical mailing list - Don & Christina PrestonMon, 28 Jan 2002 00:21:04 -0800That's right! I opened up my Idle Stabilizer Control Unit today (the one behind the right rear tail light) and snapped a couple...
- Re: Idle Stabilization parts CostsHistorical mailing list - John BangeFri, 25 Feb 2011 20:33:57 -0800...Is anyone currently experimenting with, developing, playing > with, an alternative to the VW idle stabilizer control? Someone started > out that direction but haven't...
- Re: How Long Does it Take Your Van to Warm up? Cont.Historical mailing list - James BenthallSun, 24 Apr 2005 02:23:28 EDTHi Folks, Well I disconnected my Idle Stabilizer (the one that hooks to the firewall, not the one behind the r. tail light) since...
- Vanagon Syndrome cont...Historical mailing list - Keith OvregaardTue, 11 Oct 2005 19:06:04 -0700...Fuel pump (original? no records from PO) makes normal buzzing Fuel pump relay Fuel pressure reg injectors PS pressure switch Idle stabilizer control unit...
- Help Major SurgingHistorical mailing list - Stephen FryThu, 19 Jul 2001 08:51:12 -0400...Major Surging @ 3200+ rpms, Abnormally high idle at one point around 1700 rpm Fixes: Replaced Idle stabilizer (was having a problem with high idle...
- Re: Help Losing Idle!(still)Historical mailing list - John RodgersTue, 18 Feb 2003 13:09:18 -0600Matt Sutton wrote: > > -Running engine with ISV valve disconnected, along with the single > connector to the Idle stabilizer unit behind the tailight. Been this...
- Re: Van Stalls Easily when totally cold.Historical mailing list - Scott Daniel - TurbovansFri, 19 Sep 2008 21:10:32 -0700...setting the warm idle rate to spec (850 rpms) with the adjustment screw > with > the stabilizer bypassed > a new idle stabilizer (needed one anyways...
- poor performance when hotHistorical mailing list - Keith AdamsThu, 25 Jul 2002 23:19:23 -0600...my idle stablizer valve unhooked at the moment (had a high idle) only to discover the control brain box for my idle stabilizer is...
- Re: running without idle stab unitHistorical mailing list - Ken LewisFri, 17 Feb 2006 09:34:25 -0500...running without idle stab unit Nice thing about the idle stabilizer; it produces that surge of rpms when you first start the engine. This...
- 2.1 digifant MV engine Air Flow Sensor Wiring Harness 87 VanagonHistorical mailing list - Robert Steven FishMon, 25 Feb 2002 22:49:09 +0100...I have now gone through the components which I think can be causing this, and have replaced the Idle Stabilizer Valve, the Idle Stabilizer...
- Fwd: Worse than Vanagon SyndromeHistorical mailing list - Gil NgaiThu, 13 May 2021 19:18:52 -0600...Start and run Engine - greatly improved start and idle; Inspect: Engine idles quite well without assistance of Idle Stabilizer; Reconnect Idle Stabilizer; Fuel System...
- Re: It's time to hit that idle Stabilizer on the head!!!Historical mailing list - John BangeMon, 3 Sep 2007 22:33:14 -0700...how, exactly, does the idle control unit operate the idle stabilizer valve? Having but a voltmeter, I can only tell that it receives voltage...
- Re: what is with the plugHistorical mailing list - David BeierlWed, 23 Aug 2000 00:08:40 -0400...out the idle stabilizer circuit, which adjusts timing rev-by-rev to give a steady idle under varying loads. Because the idle stab. plays...
- Re: Another hesitation question....Historical mailing list - Mark IngallsFri, 9 Feb 2001 20:51:56 -0600The 1.9's do not have a idle contol valve. They have an electronic idle stabilizer on the west engine bay. They do...
- Re: Rough running till warmed upHistorical mailing list - Craig CowanMon, 20 Aug 2007 22:23:43 -0400...Plugging >> them >> together bypasses the idle stabilizer so it won't fight idle >> adjustments >> made via the big screw in the throttle body. >> >> Don...
- Re: 84 Ignition WeirdnessHistorical mailing list - Old Volks HomeFri, 8 May 1998 20:37:37 -0700...Another possibility is the Idle Stabilizer Control Box on the left firewall. Mine tested OK at first, then intermittently - I eventually replaced it as...
- Re: Real starter problem solved, wiring harness needed - Short VersionHistorical mailing list - OlRivrRatSun, 13 Jul 2014 21:17:26 -0600...I now need the main wiring harness that runs along the front of the engine compartment to the idle stabilizer, throttle switch, injectors and...