Search messages and discussions

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 17: 16 results shown for inserts.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

• Re: trip
  Historical mailing list - David Beierl
  Fri, 10 May 2002 13:41:25 -0400
  ...Victor Truck-tire repair kit -- Tee-handle rasp, tee-handle inserting needle, tube of rubber cement and half a dozen sticky-stringy inserts. You...
• Re: Master Brake Cylinder Install
  Historical mailing list - Joel Cort
  Sat, 2 Sep 2006 21:18:30 -0700
  ...Ensure that the pushrod inserts into the MC shaft. I used the same lock-ring washers and nut although two new ones were also...
• Re: Brake master cyclinder replacement procedures (LONG)
  Historical mailing list - Joel Cort
  Mon, 17 Jul 2006 19:43:33 -0700
  ...Ensure that the pushrod inserts into the MC shaft. I used the same lock-ring washers and nut although two new ones were also...
• Re: Instructions for trans mount and master brake cylinder
  Historical mailing list - Jim Johnston
  Thu, 10 Sep 2009 08:26:40 -0400
  ...Ensure that the pushrod inserts into the MC shaft. I used the same lock-ring washers and nut although two new ones were also...
• Fwd: Brake master cyclinder replacement procedures (LONG)
  Historical mailing list - Jim Johnston
  Fri, 9 May 2008 13:13:11 -0400
  ...Ensure that the pushrod inserts into the MC shaft. I used the same lock-ring washers and nut although two new ones were also...
• 1987 Replace Heads - Thermostat Problem (long)
  Historical mailing list - Rich Dunsheath
  Sun, 27 Sep 1998 11:06:39 -0700
  ...four bolts that go through the cover and screw into brass inserts that are pressed/glued into the lower section of the thermostat housing...
• Re: Replacing the master cylider - In Bentley?
  Historical mailing list - BJ Feddish
  Fri, 9 May 2008 13:29:17 -0400
  ...Ensure that the pushrod inserts into the MC shaft. I used the same lock-ring washers and nut although two new ones were also...
• RESTORATION SAGA PII
  Historical mailing list
  Tue, 12 Sep 1995 11:47:36 -0700
  ...that I was used to in my Scirocco (400 watt halogen inserts). You know what? That little jewel (bless her heart) putted right up...
• "Smoke in the Cockpit!!!"... Vanagon Drama in Real-life, Part Deux
  Historical mailing list - Bulley
  Wed, 21 Jul 1999 18:01:12 -0400
  ...The exhaust gas recirculation system, or EGR for short, draws off a certain percentage of the exhaust product, filters it, and inserts it into...
• Re: 2.1 rebuild - new nuts for case halves-thoughts for all bolted connections.
  Historical mailing list - Scott Daniel - Turbovans
  Tue, 10 May 2011 20:37:00 -0700
  ...it used to be standard practice to bore out and tap the case for inserts, that the cyl head studs screwed into. not a...
• My on going log for this 78 x 90.5 engine (fwd)
  Historical mailing list - Gerald Skerbitz
  Mon, 17 Apr 1995 12:39:06 -0500 (CDT)
  ...Even if the Haynes book does say 25 ft lb with case inserts and 8mm studs, Ol Geno says 18 and since this a...
• Re: Questions re. Audi 3A engine swap (after searching the archives)
  Historical mailing list - Frank Grunthaner
  Thu, 6 May 2004 02:11:02 EDT
  ...Firstly, purchase four spare injector inserts for the 3A and cut them off and bore the interior to my drawing. This adapts the air...
• 87 Vanagon Engine Swap Success (LONG!)
  Historical mailing list
  Thu, 7 Dec 1995 00:48:08 -0500
  ...Broken bolt removal (1), threaded inserts (2) 90. Fuel injector 120. Towing 35. TOTAL: $2,616. I could have gotten by without replacing many...
• FRONT HEATER / BLOWER FAN - Removal Instructions - EXTREMELY VERY LONG
  Historical mailing list - Joel Cort
  Tue, 1 Dec 2009 09:29:51 -0800
  ...that it easily comes out and is held in with rubber inserts/bushings.  You will probably have to remove the squirrel cages from you...
• Re: engine change
  Historical mailing list
  Mon, 25 Nov 1996 19:52:46 -0500
  ...Broken bolt removal (1), threaded inserts (2) 90. Fuel injector 120. Towing 35. TOTAL: $2,616. I could have gotten by without replacing many...
• Re: FRONT HEATER / BLOWER FAN - Removal Instructions - EXTREMELY VERY LONG
  Historical mailing list - David Beierl
  Tue, 1 Dec 2009 15:42:16 -0500
  ...I recall that it easily comes out and is >held in with rubber inserts/bushings. You will >probably have to remove the squirrel cages...