Search messages and discussions

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 2: 22 results shown for Thrust washers.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

• Re: The pin goes in
  Historical mailing list - Stan Wilder
  Tue, 1 Jan 2002 15:47:17 -0600
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. If you...
• Re: Rebuilding an 81 Vanagon
  Historical mailing list - Stan Wilder
  Mon, 24 Dec 2001 13:28:36 -0600
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. If you...
• Differential Seal Replacement Procedure
  Historical mailing list
  Wed, 5 Jun 1996 15:44:07 -0500 (CDT)
  ...I found mine at the hardware store amongst the 'machine washers'. I find that one of these big washers against the seal does a...
• Re: 1.9L Build early stages rod question
  Historical mailing list - Jonce Fancher
  Mon, 7 Nov 2005 20:08:33 -0500
  ...The next thing that come >up when the case is align bored is that the rear main will still be loose >because the thrust...
• Hall Sender replacement on a Digifant/2.1L engine
  Historical mailing list - Mark Belanger
  Fri, 7 Mar 2003 00:22:04 -0800
  ...I promise you it will fall apart unless you're able to keep it between it's two enclosing thrust washers. Even then it...
• Re: General engine bolt/nut sizes
  Historical mailing list - Dennis Haynes
  Tue, 15 Feb 2011 01:02:26 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Re: has anyone seen July 2003 VWT?
  Historical mailing list - Stan Wilder
  Sun, 18 May 2003 12:00:55 -0700
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. Clean all...
• Re: PEX front bearings WARNING-big brake kits!
  Historical mailing list - Dennis Haynes
  Sat, 16 Jun 2012 18:56:59 -0400
  I have installed a number of those kits and have had to deal with the spacers (Lawson 5/8 washers 88451) work perfectly. Worse...
• Re: really... how tough IS a full engine rebuild?
  Historical mailing list - Stan Wilder
  Wed, 5 Feb 2003 23:26:22 -0600
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. Clean all...
• Re: 81 Westy Dead Engine - Long
  Historical mailing list - Stan Wilder
  Mon, 16 Sep 2002 00:11:03 -0500
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. Clean all...
• Engine Case and bearings
  Historical mailing list - Stan Wilder
  Sat, 25 Sep 2004 16:28:48 -0500
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. Clean all...
• Re: 87 Westy 2WD -- only reverse gear in automatic transmission works
  Historical mailing list - Rick Cooper
  Sat, 6 Dec 2014 19:34:36 -0800
  ...1) the two plastic thrust washers (oil pump - direct clutch drum, and between the direct and forward clutch drums); 2) the bearing between the...
• Re: General engine bolt/nut sizes
  Historical mailing list - Joe Luther
  Tue, 15 Feb 2011 09:16:50 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Failed Crankshaft seal yet again
  Historical mailing list - David Shepherdson
  Wed, 4 Jan 2006 17:25:28 -0800
  ...not protruding from the case Remove seal and check condition of thrust washers Try to measure crank wobble (?) Try to determine if case is...
• Re: General engine bolt/nut sizes
  Historical mailing list - Mike
  Tue, 15 Feb 2011 18:42:36 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Re: Failed Crankshaft seal yet again
  Historical mailing list - John Rodgers
  Wed, 4 Jan 2006 20:47:28 -0600
  ...not protruding from the case >Remove seal and check condition of thrust washers >Try to measure crank wobble (?) >Try to determine if case is...
• Re: What to replace in a rebuild?
  Historical mailing list - Stan Wilder
  Sun, 29 Aug 2004 18:24:18 -0500
  ...Consider using new rod nuts and crank case nuts and washers, new head bolt nuts and washers are a good idea too. Clean all...
• Re: General engine bolt/nut sizes
  Historical mailing list - Dennis Haynes
  Tue, 15 Feb 2011 20:21:35 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Re: Failed Crankshaft seal yet again
  Historical mailing list - Karl Wolz
  Wed, 4 Jan 2006 23:46:31 -0700
  ...not protruding from the case > >Remove seal and check condition of thrust washers > >Try to measure crank wobble (?) > >Try to determine if case is...
• Re: General engine bolt/nut sizes
  Historical mailing list - Mike
  Tue, 15 Feb 2011 21:19:42 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Re: General engine bolt/nut sizes
  Historical mailing list - Dennis Haynes
  Wed, 16 Feb 2011 22:02:45 -0500
  ...I've even seen my share of the cam thrust bearing wiping out. Loose heads and dropped valves are also a problem. If you...
• Re: Easiest Platform to Cnvert to I-4 FROM?
  Historical mailing list - Robert Keezer
  Tue, 27 Apr 2004 16:25:41 -0700
  ...Not only that, the load put on the 1.8 motor knocked the thrust washers into the oil pan. It's amazing the engine...