

Search messages and discussions
Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.
Page 3+: 60 results shown for Firing.
Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.
- Re: 3 probe plugsHistorical mailing list - DaveCSat, 1 Jun 2002 10:53:32 -0700...The life of the electrodes is increased by a factor of 3 (for the 3 electrode plugs) because they trade firing duty. As one...
- Re: vanagon storageHistorical mailing list - Daniel L. KatzMon, 20 Oct 2003 12:29:28 -0400...The advantage of pulling the plugs >is that your "dry" bearings are not under compression load or firing >load until they have a protective...
- Re: Points Glazed hard starting 81Historical mailing list - Larry AlofsThu, 15 Nov 2001 21:50:48 -0600...If the points were bad, the coil would not have been firing. Did you perhaps replace the rotor or cap also? Larry A.
- Cylinder NumberingHistorical mailing list - Jack NewtonTue, 9 Jan 2001 13:19:59 +1100...Can someone tell me which cylinder is which? (I took off the plug leads and according to Bentley the firing order is 1-4...
- Re: More cylinder numberingHistorical mailing listFri, 24 Jan 1997 13:23:40 +0200...The firing order, which is stamped on a sheet thin in the engines compartment, is 3-2-1-4. Do I check the manual...
- #3 late timing.Historical mailing listMon, 13 Nov 1995 19:43:59 -0800>that when timing a 1965 or later Bug, you will find that #3 >cylinder is late firing while the other three seem to check...
- Firing order for 2.0 air-cooledHistorical mailing list - Sean GarrettWed, 19 May 2004 08:14:16 -0700Don't have my Bentley today... Anyone know the order, I would guess its the same for Water-cooled too. Please pmail, I am...
- Valves adjustment in BentleyHistorical mailing list - Jim CochranFri, 21 Aug 2009 13:41:42 -0700...By next cylinder, do they mean next, as in 1-2-3-4? or next, as in firing order 1-4-3-2? Jim...
- Tips 'n' Tricks - cold cylinder checkHistorical mailing list - John RodgersMon, 23 Feb 2009 23:00:54 -0600...Trying to find the cylinder not firing? Mark the exhaust stacks just outside the cylinder with a wax crayon, The hot cyinders will burn...
- Re: Friday: Firing Up The Beast of TurinHistorical mailing list - Stephen EngelFri, 5 Dec 2014 11:38:42 -0500...it already, it's a nice little video clip > showing the firing up, for the first time in 100 years, of an amazing > Fiat...
- Re: Mis-firingHistorical mailing list - Dennis HaynesTue, 9 Oct 2007 13:31:43 -0400...Mis-firing > >I had exactly the same symptoms. The Bentley ECU pin test revealed that #1 >fuel injector was not firing and pointed to...
- Re: OK, I've had it! What now?Historical mailing list - Mark A KippertWed, 23 Sep 2009 14:17:39 -0400...So it is possible that the injectors are not firing. Mark K 1986 GL/2WD/4SPD On Sep 23, 2009, at 12:03 PM...
- Re: blinker fluid and other sundriesHistorical mailing list - Evan Mac DonaldThu, 13 Apr 2006 13:49:52 -0700...Holding down the awning Try the military suplus sites, they usually have a good supply of used firing line, quite rugged and works just...
- Re: Scrambling for an answer ~ bear with me didnt search archives... sticky injector issuesHistorical mailing list - Edward DuntzSun, 5 Dec 2010 18:43:59 -0500...my van sat for 6 days while I was on vacation and now the injectors are not firing right. I just dumped some berryman...
- Backfire vs AfterfireHistorical mailing list - John RodgersSat, 13 Aug 2005 17:39:25 -0500...Faulty valve timing and ignition timing being the primary culprits triggering firing backwards through the intake system. The engine mechanic instructors were quite adamant...
- Re: Hydraulic valve adjustment questionHistorical mailing list - Jim FelderWed, 13 Aug 2008 17:03:12 -0500...Somebody let me know if the rest of the sequence is >> anything but the firing order. >> >> Bentley says two turns of the adjusting screw...
- timing the 1.9Historical mailing list - craig cowanFri, 17 Nov 2006 19:42:03 -0500...However, we cant seem to find the firing order or which cylinder is #1. FLAPS told us #1 is passanger side front. Is that...
- Re: Technical question re: Injector firing signalHistorical mailing list - B.J.R.Fri, 10 Oct 2008 16:28:55 -0700I decided to start the diagnosis over since Ive been at it in increments for a long time. Fuel pressure YES Spark From the...
- Re: Technical question re: Injector firing signalHistorical mailing list - B.J.R.Thu, 9 Oct 2008 15:18:12 -0700...Injector firing signal My Bentley manual shows that ECU pin #1 gets the signal from the coil. This signal from one of the terminals...
- Re: More cylinder numberingHistorical mailing listMon, 27 Jan 1997 11:12:42 +0200...The firing order, which is stamped on a sheet thin in the engines compartment, is 3-2-1-4. Do I check the manual...
- Re: Technical question re: Injector firing signalHistorical mailing list - B.J.R.Thu, 9 Oct 2008 18:09:16 -0700...Injector firing signal do you know how to check continuity with a volt-ohm meter ? essential to checking wiring harness continuity. the less expensive...
- Re: Technical question re: Injector firing signalHistorical mailing list - B.J.R.Thu, 9 Oct 2008 18:12:33 -0700Re testing with a noid light... Thats a incandescent bulb my voltage light is an LED doesnt it take much less energy to light...
- Re: Surging 1.9 VanagonHistorical mailing list - Jim HenryTue, 3 Oct 2006 11:13:46 -0400...but I guess > that's because I have had it idled higher to avoid the mis > the two injectors not firing was causing. Once...
- Re: Cylinder NumberingHistorical mailing list - Simon GlenWed, 10 Jan 2001 10:31:03 +1000...Can someone tell me which cylinder is which? (I took off the > > plug leads and according to Bentley the firing order is 1-4...
- Re: Grrrr.Historical mailing list - Christopher DarilekTue, 5 Sep 2000 13:14:25 -0500...dead cyl.? Bad plug? Possible cause Means that cylinder is not firing. Could be anything from bad plug, fouled plug, bad plug wire, lack...
- Re: Technical question re: Injector firing signalHistorical mailing list - David BeierlFri, 10 Oct 2008 22:53:02 -0400At 04:28 PM 10/10/2008, B.J.R. wrote: >HOW DOES A SINGLE WIRE SIGNAL DETERMINE WHICH INJECTOR WILL FIRE?? >IE: 1...
- Re: Engine Rebuild questionsHistorical mailing list - Bradley FlubacherSun, 21 Apr 2002 01:04:51 -0400...Can someone talk me through what I need to do to get this thing >properly "timed" prior to firing it up.I have a...
- Re: Mis-firingHistorical mailing list - Brendan SlevinTue, 9 Oct 2007 09:18:24 -0700...Mis-firing I had exactly the same symptoms. The Bentley ECU pin test revealed that #1 fuel injector was not firing and pointed to...
- Re: No Power Under Load - '85 1.9Historical mailing list - Jeff LincolnWed, 21 May 2014 10:44:18 -0400...I'll check that vacuum line to - I had a big back fire when I was firing her up so it's possible something...
- Re: EmissionsHistorical mailing listSat, 30 Mar 1996 00:08:25 -0500...You either have a plug or two not firing or a cylinder with no compression. Dennis.
- Re: VW Engines and ReliabilityHistorical mailing list - Stan WilderMon, 31 Mar 2003 16:52:37 -0600...It could be a dead injector or mis firing injector causing that feeling of stress you're geerting in your engine at highway speeds...
- Re: Technical question re: Injector firing signalHistorical mailing list - Richard A JonesWed, 8 Oct 2008 13:56:22 -0600Don't let the waterboxer guys mislead you. In a waterboxer, the fuel pump runs for a few seconds when the ignition is turned...
- Re: Technical question re: Injector firing signalHistorical mailing list - Scott Daniel - TurbovansThu, 9 Oct 2008 13:43:03 -0700...Injector firing signal >I swapped a igniter one time, van would not run for anything. > that one white wire going to the ignitor had...
- Odd Engine PerformanceHistorical mailing list - jon durhamMon, 23 Jan 2012 13:16:50 -0600...But after going about a half mile, the engine begins to barely run, sometimes back firing, This goes on for about 3 minutes but...
- Re: Technical question re: Injector firing signalHistorical mailing list - David KaoWed, 8 Oct 2008 14:36:36 -0700...Injector firing signal > To: vanagon@GERRY.VANAGON.COM > Date: Wednesday, October 8, 2008, 11:04 AM > I do not know. > > Could you be more...
- Re: Technical question re: Injector firing signalHistorical mailing list - B.J.R.Thu, 9 Oct 2008 08:14:48 -0700...Injector firing signal You may want to check the two relays that are often the cause of this kind of problem, i.e. no...
- Dist Driveshaft Installation ?Historical mailing list - Christopher M. SmithThu, 30 Jan 1997 18:26:26 -0800 (PST)...plug wires (on the dist cap) to compensate for the new firing order ? That is move the #1 plug wire to what would normally...
- Re: Rotor ReplacementHistorical mailing list - Mike MillerMon, 10 Jan 2005 15:03:12 -0800No of course not its for the firing of the glow plugs. Silly. Mike On 1/10/05 2:35 PM, "Kim Brennan" <kimbrennan...
- Hydraulic valve adjustment questionHistorical mailing list - Jim FelderWed, 13 Aug 2008 14:21:14 -0500...Somebody let me know if the rest of the sequence is anything but the firing order. Bentley says two turns of the adjusting screw...
- Re: #1 firing position on 009? (2.0 l FI)Historical mailing list - Morris H. ArthurMon, 20 Nov 1995 11:46:45 -0500...Re: #1 firing position on 009? (2.0 l FI) > > Valves are adjusted relative to position of the TDC mark on the pulley -- > nothing...
- Re: Bosch 009 on T4?Historical mailing listWed, 10 Apr 1996 11:59:34 -0400...Number 2 and number 4 cylinders are not firing. I have checked the intake, points, spark plugs, plug ------- I had a 009 distribtor on...
- Re: '81.5 Diesel 1.6, Won't startHistorical mailing list - Allan StreibWed, 2 Apr 2008 11:43:31 -0400...Is it firing at ALL? Are you sure you are getting fuel to the injectors? Allan -- 1991 Vanagon GL
- Re: symptoms of running rich?Historical mailing list - Allan StreibFri, 18 Sep 2009 20:08:40 -0400Jeff Palmer <jpalmer@MTS.NET> writes: > When hot, needs to crank for a few seconds before firing. It helps if > I let the fuel...
- Re: [Re: Which cylinder isn't firing??]Historical mailing list - d tSat, 4 Nov 2000 19:57:56 MSTBradley Flubacher <flubach@HOME.COM> wrote: > I thought this was a no-no as per the bentley manual. It has warnings about > not disconnecting...
- Help! Won't StartHistorical mailing list - Don & Christina PrestonSun, 17 Dec 2000 17:45:52 -0800...I have my Digitool hooked up and it shows that the Injectors and the coil aren't firing. Did I forget something? I've...
- Re: Diaganosing Fuel Injection SystemsHistorical mailing list - Jeff DieboltTue, 25 Feb 1997 08:56:59 -0500...With this information it adjusts the duration of the injector firing for proper mixture. The coil wire is only to tell where the distributor...
- Re: AFM intermittancy result?Historical mailing list - Karl WolzThu, 12 Aug 2010 10:02:40 -0700...When that happens, the AFM's wiper will swing to another part of |the track, causing the ECU to start firing the injectors again...
- Re: Sorta Scary EventHistorical mailing list - David BeierlSat, 26 Feb 2011 09:11:15 -0500...if the tach drops like a stone while the engine is still turning, then firing impulses are not reaching the spark coil primary, since...
- Re: Strange Vanagon problem in BelizeHistorical mailing list - mark drillockThu, 13 Jan 2011 06:48:08 -0800compression good? fuel pressure good? making spark? timing close? firing order right? injectors spraying? is the exhaust/cat plugged or blocked? Should at least...
- Re: Friday: Firing Up The Beast of TurinHistorical mailing list - Jim FelderFri, 5 Dec 2014 10:08:22 -0600...it already, it's a nice little video clip > showing the firing up, for the first time in 100 years, of an amazing > Fiat...
- firing on 3 cylinders.Historical mailing list - craig cowanSun, 19 Nov 2006 15:15:43 -0500...However, we wanted to rule out that one of the cylinders wasnt firing, so while selectively removing the plug wires from the cap, we...
- Re: Mis-firingHistorical mailing list - Mike CollumTue, 9 Oct 2007 12:32:11 -0400...Mis-firing > > I had exactly the same symptoms. The Bentley ECU pin test revealed that #1 > fuel injector was not firing and pointed to...
- Re: Injectors not firing ?Historical mailing list - Dennis HaynesSat, 24 Feb 2007 04:16:58 +0000...Injectors not firing ? To: vanagon@GERRY.VANAGON.COM > Hey everybody > Well, I bought another one ( never heard that before huh? ) > > I have a 91...
- RE: Newbe Fridge QuestionHistorical mailing list - Tom ForhanThu, 04 Jan 96 16:53:25 -0500...Just keep on clicking it as rapidly as possible, keep firing away until it lights. Mine never works on one click, but always fires...
- Re: FI help neededHistorical mailing listSat, 5 Oct 1996 05:44:18 -0400...van back on the road! >> Don, have you made sure the firing order is correct, and the distributor is geared correctly?If it is...
- Re: Technical question re: Injector firing signalHistorical mailing list - David KaoThu, 9 Oct 2008 18:39:10 -0700...Injector firing signal > To: vanagon@GERRY.VANAGON.COM > Date: Thursday, October 9, 2008, 6:09 PM > Here IS A diagram of the system > > http...
- Re: Technical question re: Injector firing signalHistorical mailing list - David KaoThu, 9 Oct 2008 10:55:29 -0700...Injector firing signal > To: dtkao0205@yahoo.com, vanagon@GERRY.VANAGON.COM > Date: Thursday, October 9, 2008, 8:14 AM > thanks David. > But that is...
- 84 Westy emgine missing/fuel starvedHistorical mailing listWed, 4 Sep 1996 08:21:40 +1000...While in Hood River, OR she started miss firing and hesitating intermittantly. It got worse but not so bad that we had to do...
- Re: Throttle Switch and Failure to Start.Historical mailing list - Dennis HaynesSun, 19 Apr 2015 22:14:16 -0400The throttle switch isn’t keeping it from firing. Since the switch is closed, (on), with the throttle fully closed or open why would...
- Fridge, keeps blowing out and backfires durring ignitionHistorical mailing list - Jay lefsteinThu, 26 Aug 2010 18:43:31 -0700...My fridge keeps blowing out, hard starts sometimes and some back firing.. I had it out and did the valve upgrade.. It seems to...