← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 4+: 60 results shown for Exhaust outlet.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

Re: New motor selections for vanagons.
Historical mailing list - PAT
Mon, 18 May 1998 19:48:54 -0400
...The exhaust outlet from the turbo elbows down, pointing at the ground. A couple 2.5 inch 90's and a 2.5 flowmaster...
Re: Long Block Advice
Historical mailing list - Erik O
Mon, 03 Feb 1997 11:32:33 -0800
...Not > sure about exhaust, maybe custom fab something using a dual outlet > GTI manifold, or one from a Fox. The stock diesel is single...
Re: Swap update: Dasher Manifolds
Historical mailing list - Erik O
Tue, 12 May 1998 10:12:23 -0400
...The outlet is offset of the center, just looks different for some reason. I don't think I'll have any trouble with flow...
Re: '88 GL - Gradual Power Loss
Historical mailing list - Joel Cort
Tue, 27 Mar 2012 05:24:34 -0700
...engine > 2) Funny exhaust sound (somewhat of a "Hissing" sound) > 3) Place a vacuum gauge on a intake side outlet. Gauge will read almost...
Re: Vanagon exhaust diameter? + Custom exhaust fabrication questions.
Historical mailing list - neil N
Fri, 28 Mar 2008 13:29:38 -0700
...muffler with 2" inlets/outlets. > >> > > >> > After the collector, the Jetta is 2" pipe. > >> > > >> > What is the diameter of exhaust pipe on the Vanagon? > >> > > >> > Can...
Re: camper heating
Historical mailing list - Robert Fisher
Sat, 16 Oct 2004 14:25:14 -0700
...from > heat exchanger on exhaust. > Al Brase > > tmiller wrote: > >> Maybe you can hang a heat exchanger at the exhaust outlet and let the >> engine...
Re: 90+ Fox engine @ 54 degrees
Historical mailing list - David Marshall
Wed, 25 Sep 2002 19:40:20 -0700
...It is more than the exhaust manifold that makes the low 81hp output of these motor. The compression ratio is 8.5:1 and...
Re: Performance Mufflers.
Historical mailing list - Frank Condelli
Mon, 8 Jan 2001 06:05:55 EST
...Steve, being the main promoter of the STEBRO/Vanagon Stainless Steel Exhaust System I have to jump in here. The STEBRO Muffler for the...
Re: insulating hot side of Dometic refer
Historical mailing list - neil n
Sun, 25 Sep 2011 10:03:04 -0700
...the classic exhaust fan in the >> former city water inlet door which should help, and putting in a �12V >> accessory outlet next to the...
Re: 2.0l conversion
Historical mailing list - Randolph Feuerriegel
Tue, 21 Sep 1999 12:42:37 -0700
...Originally I had an exhaust manifold with one outlet which was quieter and less vibration, but the 2 into 1 downpipe dramatically increased my...
The water heater project
Historical mailing list
12 Jan 95 14:45
...Cooling the exhaust might result in large exhaust pressure difference for number 3 cylinder - something to think about. Ok so then fit a water...
Re: Heater
Historical mailing list - Dave Vickery
Sat, 2 Dec 2006 16:42:14 +0000
...outlet on the end and it seems to have been diassambled, painted, reassembled and the wiring looks a little changed to me. The exhaust...
Re: Exhaust Bushing Inner Weave Premature Failure
Historical mailing list - Don Hanson
Fri, 7 Feb 2014 12:12:05 -0800
...The diesel vanagon exhaust mounts, they are not very forgiving. most exhaust systems have some give..some flex. Ours have to be correct, or...
Re: Bad juju?
Historical mailing list - Mike
Tue, 13 Feb 2007 13:18:10 -0500
...opening each outlet at the wheels > individually? I don't have anybody to pump the brakes for me. > > For checking exhaust leaks, I took...
Re: '82 Jetta conversion exhaust
Historical mailing list - Kenneth Wilford
Tue, 13 Aug 2002 11:33:48 -0400
I have the exhaust manifolds in stock that Tiico is using for thier conversions. It is a 4 to 2 manifold with the outlet...
Re: Dometic Fridge Mod Update
Historical mailing list - Todd Last
Thu, 28 Jun 2007 19:29:14 +0000
...intake/exhaust/drain tubes, added check valve > to pump, reamed out pump outlet, added extra pump inlet hole, wrapped > intake and exhaust flues and...
Re: Vanagon exhaust diameter? + Custom exhaust fabrication questions.
Historical mailing list - neil N
Thu, 27 Mar 2008 20:58:29 -0700
...muffler with 2" inlets/outlets. > > > > > > After the collector, the Jetta is 2" pipe. > > > > > > What is the diameter of exhaust pipe on the Vanagon? > > > > > > Can...
Re: 90+ Fox engine @ 54 degrees
Historical mailing list - Don Hundt
Wed, 25 Sep 2002 23:32:41 -0700
I have a jh engine from an 83 gti in my van, early rabbit intake, fox 4 into 1 exhaust mainfold. I didn't...
VW Howard looking for ideas...
Historical mailing list - Jim Arnott
Fri, 1 Jun 2001 08:32:06 -0700
...However, the exhaust collector pipe is now broken for the 2nd time. This pipe is located just below the exhaust manifold. It is shaped...
Re: vanagon Digest - 8 Mar 2008 (#2008-289)
Historical mailing list - sam mccarthy
Sat, 8 Mar 2008 22:00:45 -0800
...The first set up I had built at a exhaust shop using an old Dasher dual outlet manifold, which angles toward the front of...
Inline Exhaust Theory: part II
Historical mailing list - Erik O
Tue, 19 May 1998 12:59:51 -0400
...Alright, now I have this donut outlet manifold to finish up with the rest of the exhaust system. The Golf manifold I'm using...
Re: Loud Fuel Pump/Fuel Pump Mount - Was: Thank you Go Westy
Historical mailing list - neil n
Mon, 15 Mar 2010 12:38:09 -0800
...Pretty sure both your Vanagons have the larger ID on tank outlet. Plus you wouldn't be prone to using a zap strap. <grin...
Re: Bad juju?
Historical mailing list - aatransaxle
Tue, 13 Feb 2007 18:01:21 -0800
...opening each outlet at the wheels > individually? I don't have anybody to pump the brakes for me. > > For checking exhaust leaks, I took...
Eurospec questions.
Historical mailing list - Jim DiGennaro
Fri, 15 Oct 1999 21:55:16 -0400
...Is Eurospec using the same components or are they fabricating their own parts? What type of exhaust manifolds are they using? In the interest...
Re: Re-introduction & Dash Removal Question
Historical mailing list - Neil N
Sun, 23 Feb 2014 16:10:34 -0800
...Windshield wiper shafts ok? Clean up any messy wiring. (from dreaded previous owner) Check if cigarette lighter outlet loose. If you see evidence of...
Re: Grills, grills, grills
Historical mailing list - Alistair Bell
Tue, 24 Aug 2021 17:29:50 -0700
Mmm Neil… plexi…with lights… But, it gets close to the exhaust pipe of fridge. I know we both have lagged that pipe, but...
Re: Oil question....not the dreaded which motor oil is best
Historical mailing list - Kent Christensen
Sun, 30 Dec 2012 16:03:44 -0700
...traditional diesel smell nor is there black soot all over the exhaust outlets or the rear of the car. This has also nothing to...
hesitation when I hit the gas...
Historical mailing list - gary goldey
Wed, 29 Jun 2005 23:52:55 -0700
...I have this fear of something breaking...(like the exhaust stud thing).. I also had this whiny fuel pump which I switched out with...
Re: AC While Camping - Portable Unit
Historical mailing list - David Beierl
Wed, 9 Jun 2010 20:07:14 -0400
...I don't recall seeing big exhaust ducts -- I wonder if they're water-cooled. That's how I'd do it, so you...
Re: Contents of Head Gasket Kit 025 198 102A 025198102A (repost)
Historical mailing list - Michael Knight
Tue, 29 Mar 2005 17:14:47 -0600
...I'd say exhaust (metal gasket) (???) >13) ??? Thermostat Housing Outlet Flanged Nipple to Head, Gasket. 1.9L >14) Exhaust manifold gaskets. No sealant >15...
Re: Fire (update)
Historical mailing list - Aaron Pearson
Fri, 30 Sep 2005 14:56:15 -0600
...and the exhaust outlet are all sealed from the inside of the Vanagon. The only openings are at the reefer exhaust port on the...
Re: Cut tranny input shaft while still in tranny? (for engine conversion)
Historical mailing list - neil N
Sat, 8 Mar 2008 11:46:46 -0800
...But that just sounds like too much work and way beyond my current, uh, welding "skills". --- ;^) I'll look for a dual outlet exhaust...
Re: mystery vents
Historical mailing list - John Bange
Fri, 11 Apr 2008 10:14:12 -0700
> 1) Where does the exhaust air go from the vents on the lower > back corner of the front doors in a 1983 V'gon...
Re: Oil pump day..
Historical mailing list - Dennis Haynes
Sun, 1 May 2016 00:51:53 -0400
...If not a tight fit they can leak at both the inlet and outlet both of which will reduce oil pressure. Send the defective...
Re: Air cooled heater idea/questions
Historical mailing list - Edward Maglott
Sun, 4 Feb 2007 21:52:18 -0500
...1/2" soft copper pipe around each exhaust pipe, > >assemble/install boxes, (plug hot air outlets) > >connect copper coils to create a circuit > >install...
Re: Engine from '79 westie to '81 AirCool
Historical mailing list - Carrington, Tom
Mon, 4 Oct 1999 11:26:27 -0400
...The '81 will have rectangular exhaust ports and the '79 has round ports. Of course, that means the heat exchangers are different, too. The...
Re: FS: '86 Syncro Wkndr, ALSO: fridge Q, "weekender cabinet" project
Historical mailing list - S Sittservl
Tue, 10 Aug 1999 23:10:28 EDT
...and exhaust pipes enough > so they will reach the sliding window, then constructing a narrow > "window-insert" flue with the inlet and outlets stacked...
Re: Final stage of my long term fuel pump issue - what would you do?
Historical mailing list - Frank Condelli
Thu, 19 Oct 2006 06:51:51 EDT
...Damaging fuel contaminants can indeed be smaller than the outlet screen on the tank. Greg, sorry but your wrong on this one. The filter...
Re: Alternative mufflers in place of OEM etc..
Historical mailing list - Michael Blackburn
Fri, 5 Jul 2002 08:35:49 -0600
...The shop used a standard '5" Dodge Can' and welded the exhaust flange from the old muffler onto it. The Dodge can is a...
Re: Dometic Fridge: Bah Humbug! <grin>
Historical mailing list - Alistair Bell
Wed, 11 Aug 2010 12:40:44 -0700
...Offset "O" on AL piece over exhaust outlet as per this pic: http://tinyurl.com/34rcuex Is that correct? Never give up yes. But...
Re: Dometic Fridge Mod Update
Historical mailing list - Keith Ovregaard
Thu, 28 Jun 2007 12:48:49 -0700
...intake/exhaust/drain tubes, added check >> valve >> to pump, reamed out pump outlet, added extra pump inlet hole, wrapped >> intake and exhaust flues and...
Re: '88 GL - Gradual Power Loss
Historical mailing list - J Stewart
Tue, 27 Mar 2012 16:36:52 +0000
...engine > > 2) Funny exhaust sound (somewhat of a "Hissing" sound) > > 3) Place a vacuum gauge on a intake side outlet. Gauge will read > > almost...
Re: Vanagon exhaust diameter? + Custom exhaust fabrication questions.
Historical mailing list - Jake de Villiers
Thu, 27 Mar 2008 21:36:10 -0700
...muffler with 2" inlets/outlets. > > > > > > > > After the collector, the Jetta is 2" pipe. > > > > > > > > What is the diameter of exhaust pipe on the Vanagon? > > > > > > > > Can...
Various Upgrades for Lilleyed WBX... PT2
Historical mailing list - Robert Lilley
Mon, 29 Oct 2001 23:13:03 EST
...This keeps the exhaust gases hotter and helps to maintains a high exhaust gas velocity throughout the pipe. This allows the exhaust to have...
Re: camper heating
Historical mailing list - Robert Fisher
Sat, 16 Oct 2004 14:46:14 -0700
...from >> heat exchanger on exhaust. >> Al Brase >> >> tmiller wrote: >> >>> Maybe you can hang a heat exchanger at the exhaust outlet and let the >>> engine...
A Vibration Free TIICO Exhaust System - A Sucessful Work in Progress
Historical mailing list - Ed McLean
Mon, 16 Sep 2002 23:40:16 -0400
...Attached to the converter is a 6" flexible exhaust section followed with a 4"x9" oval muffler 18" long. The outlet end of the...
Re: On exhaust cracking,vibration and noise(not short)for converted vgons
Historical mailing list - Robert Keezer
Fri, 28 Sep 2001 13:26:51 EDT
Frank, Forget that trip to the Moon-wer'e going to Mars!! I have been experimenting myself with exhaust configurations however without the advantage...
Back on heating
Historical mailing list
3 Feb 95 16:47
...However the heat exhausting from the tinware at the bottom is damn hot after five minutes. So check out my latest ASCII design:- cool...
Re: Engine from '79 westie to '81 AirCool
Historical mailing list - Max/Joyce Wellhouse
Mon, 4 Oct 1999 02:41:56 -0700
...I was fortunate that I had the later design square port exhaust flanges like the vanagon air cooleds had. Next you need to change...
'87 Westie FS in NJ for $10,500
Historical mailing list
Mon, 19 Jul 1999 09:01:38 EDT
...Also has some minor bumps and scrapes but also nothing ugly.) California Van so no rust (not even on the exhaust system!). Around 100k...
Re: Eurospec stuff
Historical mailing list - David Marshall
Fri, 29 Oct 1999 20:13:50 -0700
...My exhaust systems that are in my two demo vans are simple dual outlet Audi 80 manifolds that go into a canister muffler - no...
Re: Vanagon Water Temp Gauge - Temperatures?
Historical mailing list - Max Wellhouse
Sun, 17 Aug 2008 09:46:23 -0500
...I have a separate water temp gauge with the sender mounted in the skinny hose that comes off the #4 cylinder outlet and the...
Re: Performance Mufflers.
Historical mailing list - Mark Dorm
Mon, 8 Jan 2001 21:41:03 -0800
...This muffler is made with a >"flow >thru" design, there are no baffles in the way of the exhaust flow, >therefore >there is a...
Re: fuel pump fuel filter-stupid engineering
Historical mailing list - Frank Condelli
Sat, 20 Jan 2007 06:39:10 EST
...It does not extend all the way to the outlet nipple on the outside of the tank. If it just runs a few inches...
FS: 1990 Vanagon Carat - Capitola, CA
Historical mailing list - Frank Condelli
Thu, 12 Jun 2008 06:43:45 EDT
...Complete stainless steel exhaust system. Complete brake rebuild including all parts rust proofed with POR-15ed. Complete fuel tank rebuild including new sender, lines...
Re: diesel gas conversion - which header?
Historical mailing list - David Marshall
Mon, 6 May 2002 18:38:59 -0700
The best fitting I have used is the dual outlet Audi 80 manifold - it also flows well too! Currently on my 2.0L Digifant...
Re: Winters in the van...
Historical mailing list - Isaac Taylor
Sat, 16 Nov 2002 07:13:16 -0500
Hey that stovetop heater exhaust idea has potential. You can solve the exhaust problem by installing your draw fan as the exhaust outlet, flush...
Re: Air cooled heater idea/questions
Historical mailing list - neil
Wed, 7 Feb 2007 09:47:59 -0800
...1/2" soft copper pipe around each exhaust pipe, > > assemble/install boxes, (plug hot air outlets) > > connect copper coils to create a circuit > > install...
RE: Buy of the Day
Historical mailing list - Erik O
Fri, 15 Nov 1996 19:57:56 -0800
...There were two outlets for the exhaust about a foot > apart and had two very small heat exchanger type structures. Any one > interested in...
Re: Vanagon exhaust diameter? + Custom exhaust fabrication questions.
Historical mailing list - neil N
Thu, 27 Mar 2008 22:16:42 -0700
...muffler with 2" inlets/outlets. > > > > > > > > > > After the collector, the Jetta is 2" pipe. > > > > > > > > > > What is the diameter of exhaust pipe on the Vanagon? > > > > > > > > > > Can...