Skip to main content
Gerry | Vanagon
Checking account...
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 5+: 60 results shown for Clutch Release Bearing.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Re: Clutch/Shifting issue?
    Historical mailing list - Tom Buese
    Mon, 25 Jul 2011 16:15:42 -0600
    ...to pilot bearing failure easily. > that failure can show up as intermittant failing to get a clean release of the clutch. > > how does the...
  • Re: clutch shudder?
    Historical mailing list - Mike Collum
    Tue, 2 Aug 2005 14:39:39 -0400
    ...Of course you'll replace the throwout bearing and you >> should either true up the release fork or replace it along with >> checking/replacing...
  • Crankshaft end float.
    Historical mailing list - Stan Wilder
    Tue, 21 May 2002 16:41:22 -0500
    ...on the disk it can cause the clutch to chatter, hang up and not fully release. Stan Wilder ________________________________________________________________ GET INTERNET ACCESS FROM JUNO! Juno...
  • Re: transmission
    Historical mailing list - David Kao
    Fri, 14 Dec 2007 14:58:04 -0800
    ...But as soon as I gradually release the pedal (begin to engage the clutch) the noise begins. This includes that the gear is in...
  • Gear Problems?? 87GL rebuild update
    Historical mailing list - Racer X
    Wed, 25 Nov 1998 21:53:59 +0000
    ...I put in a new clutch, disc, pilot bearing, release bearing along with the engine rebuild. Tonight I was going to get it off...
  • Re: 84 Westy std. trans
    Historical mailing list - Dennis Haynes
    Mon, 13 May 2002 18:33:49 -0400
    ...2nd gear seems to be the first to complain when the clutch does not release right or if the pilot bearing is bad. Dennis...
  • Re: Can pilotbearing be changed with flywheel in place?
    Historical mailing list - David Kao
    Sun, 10 Jun 2007 08:11:05 -0700
    ...bearing cross shaft can wear in an uneven fashion as to > push on the pressplate so it chaters or does not release properly. > If...
  • Re: [VB] Clutch Part numbers -- Tranny and Engine OUT- Parts Described.
    Historical mailing list - Stan Wilder
    Sun, 2 Feb 2003 16:52:31 -0600
    ...drill holes you won't find in pure stock flywheels. #8) Clutch release levers are still plenty meaty and show even normal wear. Since...
  • Re: Metallic sound when depressing the clutch
    Historical mailing list - Kim Brennan
    Fri, 3 Jul 2009 23:58:00 -0400
    Throw out bearing is the first thought to come to mind. With the engine running, and the gear in neutral, try pressing the clutch...
  • EV trans removal
    Historical mailing list - Mike Catlin
    Wed, 6 Aug 1997 08:23:01 -0700
    ...bolt that is used to hold the throw-out lever > > and release bearing away from the pressure plate to allow for easier > removal > > of...
  • Re: Have you ever broken a clutch by push starting a vehicle?
    Historical mailing list - Jake de Villiers
    Sun, 25 Nov 2007 10:09:54 -0800
    ...It sounds like you damaged the > throwout bearing, or a the clutch. Inspect > first, then decide what parts are needed. > > My kids something similar...
  • Re: clutch shudder?
    Historical mailing list - Jake de Villiers
    Tue, 2 Aug 2005 19:09:03 -0700
    ...clutch shudder? > Will > > My 84 Westy has had that same shudder for years and I had a new > clutch/pilot bearing and resurfaced flywheel...
  • Re: Clutch repairs, was "Is mechanic on the level?"
    Historical mailing list - The Henrys
    Sun, 31 Jan 1999 10:51:28 +0000
    ...I my case, the PO has replaced the clutch and throw out bearing at 80 k miles and again at 90 k miles and...
  • Re: Is mechanic on the level?
    Historical mailing list - David-M
    Sat, 30 Jan 1999 05:40:00 -0500
    ...Other than some > intermittent screeching with the clutch pedal out (Most people said pilot > bearing), it drove as it always has. It shifted fine...
  • <No subject>
    Historical mailing list - Todd Lund
    Wed, 21 Aug 2002 09:47:25 -0700
    ...Rebuilt manual transmission and new clutch disc, pressure plate and release bearing at 63,183 miles, on 08/26/00 (supplied by AA Transaxle...
  • Re: Clutch pedal goes only halfway
    Historical mailing list - Skip
    Wed, 9 May 2012 00:06:49 +0000
    ...Clutch pedal goes only halfway Under normal operation the clutch pressure plate pushes the driven (slave), cylinder back in when the pedal is released...
  • Re: transmission
    Historical mailing list - Dennis Haynes
    Fri, 14 Dec 2007 18:17:46 -0500
    ...But as soon as I gradually release the pedal (begin to engage the clutch) the noise begins. This includes that the gear is in...
  • Re: Failing clutch master or slave?
    Historical mailing list - Chris S
    Wed, 30 Jun 2021 12:33:01 -0400
    ...one clutch slave cylinder bolt missing. Other bolthole cracked. > Slight problem: clutch release bearing contact surfaces worn square on release fork. > > Good news: clutch...
  • Re: Have you ever broken a clutch by push starting a vehicle?
    Historical mailing list - Clint Kolda
    Sun, 25 Nov 2007 08:24:13 -0800
    ...It sounds like you damaged the throwout bearing, or a the clutch. Inspect first, then decide what parts are needed. My kids something similar...
  • Re: Shifting Shudder Part II
    Historical mailing list - Al and Sue Brase
    Thu, 16 Sep 2004 23:30:11 -0500
    ...The clutch cannot possibly release smoothly if the bearing surface is not parallel to the flywheel. Al Brase 69 doublecab, Vanagons John Rodgers wrote...
  • Re: Is mechanic on the level?
    Historical mailing list - DAVID MOST
    Sun, 31 Jan 1999 08:37:01 -0800
    ...Other than some > > intermittent screeching with the clutch pedal out (Most people said pilot > > bearing), it drove as it always has. It shifted fine...
  • Re: Clutch Pedal Does Not Move
    Historical mailing list - Jake de Villiers
    Wed, 5 Jul 2006 16:43:31 -0700
    Which one of you was responsible for the initial work, including not replacing the throw-out bearing? I'm just wondering. Jake On 7...
  • Re: symptoms of a failing clutch
    Historical mailing list - Ben McCafferty
    Wed, 11 Dec 2002 16:41:10 -0700
    ...In the last few > days I've had to floor the clutch pedal in order to shift gears. The > gears engage when I release...
  • Re: Failing clutch master or slave?
    Historical mailing list - Alistair Bell
    Wed, 30 Jun 2021 17:56:19 -0700
    ...one clutch slave cylinder bolt missing. Other bolthole cracked. >> Slight problem: clutch release bearing contact surfaces worn square on release fork. >> >> Good news: clutch...
  • Re: 90 Syncro weak clutch spring?
    Historical mailing list - Bret Berger
    Fri, 1 Apr 2011 17:12:57 -0600
    ...fingers far enough so the grip on the clutch > disc is released. > >> 1990 Syncro symptoms: clutch arm sticking out of transmission does not >> push...
  • Re: Can pilotbearing be changed with flywheel in place?
    Historical mailing list - Bob Donalds
    Sun, 10 Jun 2007 09:06:20 -0700
    ...bearing cross shaft can wear in an uneven fashion as to push on the pressplate so it chaters or does not release properly. If...
  • Re: Clutch pedal goes only halfway
    Historical mailing list - Dennis Haynes
    Mon, 7 May 2012 18:04:30 -0400
    Under normal operation the clutch pressure plate pushes the driven (slave), cylinder back in when the pedal is released. Without the pressure plate the...
  • Re: shifting anomaly ...
    Historical mailing list - Neil N
    Mon, 5 Oct 2015 10:02:51 -0700
    ...These symptoms sound like clutch release issue. -- Neil n Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca> 1988 Westy Images <https://picasaweb.google.com...
  • Re: Hi list. 90 syncro bad leak stuck in parking lot
    Historical mailing list - Jim Felder
    Thu, 26 Jun 2014 16:30:26 -0500
    ...seal can leak without much oil getting into the clutch disc. > The release bearing operating sleeve is designed to catch leaking tranny > oil and...
  • Re: Clutch problems
    Historical mailing list - Al and Sue Brase
    Mon, 8 Nov 2004 10:13:16 -0600
    ...I >> have just completely my Subaru conversion and went with an upgraded >> Luk clutch kit with a new disc, pressure plate, and release bearing...
  • Procedure: Replacing the trans main shaft oil seal
    Historical mailing list - Tom Young
    Thu, 15 Jul 1999 20:31:54 -0700
    ...Unclip the release (throwout) bearing from the release lever and swing the release lever up out of the way. Remove the 3 bolts that...
  • Re: Clutch pedal goes only halfway
    Historical mailing list - Dennis Haynes
    Wed, 9 May 2012 00:01:42 -0400
    ...Clutch pedal goes only halfway Under normal operation the clutch pressure plate pushes the driven (slave), cylinder back in when the pedal is released...
  • Re: clutch hydraulics or more serious?
    Historical mailing list - Dennis Haynes
    Sat, 20 Mar 2004 10:12:26 -0500
    ...If the pedal stays firm then maybe there is another problem with the clutch, release bearing, or trans input shaft that wasn't discovered...
  • Re: was: Friction, any extra wear 'n tear?
    Historical mailing list - levi hawkins
    Wed, 22 Jul 2009 14:21:37 -0700
    ...bearing is not relevant because it is just the engine vs. the clutch fork. ���Now of course if the clutch doesn't release completely...
  • For Sale 88 Westfalia
    Historical mailing list - Todd Lund
    Wed, 21 Aug 2002 09:49:26 -0700
    ...Rebuilt manual transmission and new clutch disc, pressure plate and release bearing at 63,183 miles, on 08/26/00 (supplied by AA Transaxle...
  • Re: Crank shaft seal front and back
    Historical mailing list - Bradley Flubacher
    Sun, 10 Mar 2002 14:37:01 -0500
    ...the main seal, "O" ring, and a new clutch pilot bearing and clutch release bearing. Also a new tranny shaft seal and a new...
  • Re: Is mechanic on the level?
    Historical mailing list - The Bus Depot
    Wed, 3 Feb 1999 23:21:22 -0500
    ...a clutch replacement, and the service manager > called me the next day to tell me that not only was my throw out bearing > bad...
  • Re: Clutch problems
    Historical mailing list - Herr Wibo Fichten
    Sun, 18 Jan 2004 20:40:54 -0400
    ...Clutch problems > On Christmas Eve, my '84 camper went in to have its rear main bearing seal > replaced (for which on an 84 you...
  • Re: Clutch pedal goes only halfway
    Historical mailing list - George Laubach
    Wed, 9 May 2012 06:17:23 -0500
    ...Clutch pedal goes only halfway > > Under normal operation the clutch pressure plate pushes the driven (slave), cylinder back in when the pedal is released...
  • Re: return mechanism for throw-out fork?
    Historical mailing list - Dennis Haynes
    Sat, 6 Aug 2011 09:25:39 -0400
    No return spring for the hydraulic clutch set up and yes it is normal for the release bearing to always be in contact with...
  • Re: clutch shudder
    Historical mailing list - Stan Wilder
    Mon, 27 Aug 2001 19:53:30 -0500
    ...me wonder what parts they did replace, since the bearing comes > with > the clutch kit... Did they order the parts a la carte? They...
  • Clutch replacement report - longish
    Historical mailing list - Alistair Bell
    Fri, 16 Mar 2001 11:58:12 -0800
    ...I thought it possible that this was the original clutch. I bought a Sachs clutch replacement kit (complete with new throw-out bearing and...
  • Re: 85 Vanagon - Clutch throw-out level movement ?
    Historical mailing list - Scott Daniel - Shazam
    Sat, 1 Dec 2007 20:11:42 -0800
    ...I have > done very few clutch jobs that only needed a release bearing so it really > is not an issue. > > Dennis > > -----Original Message----- > From...
  • A movie with Bob
    Historical mailing list - The Westy man
    Thu, 23 Oct 2008 17:22:09 -0700
    ...my clutch on my 87 syncro. >>>> >>>> I am getting a clutch kit which includes " Pressure Plate - Clutch >>>> Disc - >>>> Throw-out Bearing - Clutch Disc Alignment...
  • Re: Clutch Cross-shaft Question
    Historical mailing list - neil n
    Mon, 5 Apr 2010 11:48:26 -0700
    ...Clutch Cross-shaft Question > > ....... > I guess VW figured that > since arms only push out the throw out bearing, they only need a weld > at...
  • Re: Difficulty / time to replace clutch - 1991 Westfalia 2WD
    Historical mailing list - Jim. Felder
    Mon, 14 Dec 2020 20:17:57 -0600
    ...This is the time to pop in a new clutch release bearing. While it is out it is time to replace the transmission shaft...
  • Re: Metallic sound when depressing the clutch
    Historical mailing list - neil N
    Fri, 3 Jul 2009 18:29:38 -0700
    ...If you hear the noise when clutch pedal depressed, then noise goes away when pedal let up, it might be the throw out bearing...
  • Re: Have you ever broken a clutch by push starting a vehicle?
    Historical mailing list - Paul N. Oliver
    Sun, 25 Nov 2007 09:58:36 -0600
    It sounds like you damaged the throwout bearing, or a the clutch. Inspect first, then decide what parts are needed. My kids something similar...
  • Re: Clutch problems
    Historical mailing list - John Rodgers
    Sun, 18 Jan 2004 19:48:57 -0600
    ...Clutch problems > > > > >>On Christmas Eve, my '84 camper went in to have its rear main bearing seal >>replaced (for which on an 84 you...
  • Re: Can pilotbearing be changed with flywheel in place?
    Historical mailing list - Bob Donalds
    Sun, 10 Jun 2007 12:07:57 -0700
    ...bearing cross shaft can wear in an uneven fashion as to >>push on the pressplate so it chaters or does not release properly. >>If...
  • Re: Longer Lasting Clutch?
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 25 Apr 2011 20:13:16 -0700
    ...might not release fully with a thicker disc. Someone just suggested to a client/friend of mine .. get a ceramic racing clutch and it...
  • Re: was: Friction, any extra wear 'n tear?
    Historical mailing list - Mike
    Wed, 22 Jul 2009 18:22:46 -0400
    ...bearing is not relevant because it is just the engine vs. the clutch fork. Now of course if the clutch doesn't release completely...
  • Re: transmission
    Historical mailing list - David Kao
    Fri, 14 Dec 2007 16:00:05 -0800
    ...clutch down gives noise - you think of TOB > > If clutch pedal down equals quiet, you think of transmission main shaft > > and/ or bearings usually...
  • Re: clutch hydraulics or more serious?
    Historical mailing list - Keith Hattrup
    Sat, 20 Mar 2004 07:27:00 -0800
    ...If the pedal > stays firm then maybe there is another problem with > the clutch, release > bearing, or trans input shaft that wasn't discovered...
  • Re: Transmission swap problems: 86 tranny onto 83 engine.
    Historical mailing list - Rick Cooper
    Tue, 5 Jan 2016 14:11:24 -0800
    ...So the clutch disk could not have moved out of center. Mark, I'm just reading up on the pilot bearing issue. Guess I...
  • Re: Leslie's tumbling rock noise
    Historical mailing list - Todd Hill
    Sat, 25 Jul 1998 03:07:17 EDT
    ...It is especially noticable in first gear and reverse. >> To which Larry Hamm replied: // Probably the throwout bearing (release bearing), but it wouldn't...
  • Re: Crankshaft end float.
    Historical mailing list - Thomas D. Hanlon
    Wed, 22 May 2002 00:26:30 -0700
    ...on the disk > it can cause the clutch to chatter, hang up and not fully release. > > Stan Wilder > > ________________________________________________________________ > GET INTERNET ACCESS FROM JUNO! > Juno...
  • My 'new' '86 Vanagon
    Historical mailing list - Michael Harris
    Sat, 18 Nov 1995 02:33:22 -0800
    ...clutch 'kit' - consisting of clutch plate, pressure plate and release bearing. Is this a good price? It looks quite simple to do the clutch...
  • Re: Clutch issues
    Historical mailing list - aatransaxle
    Sun, 10 Jun 2007 10:06:44 -0700
    ...bearing cross shaft can wear in an uneven fashion as >>>>to push on the pressplate so it chaters or does not release properly. >>>>If...
  • Re: Clutch pedal goes only halfway
    Historical mailing list - Scott Daniel - Turbovans
    Tue, 8 May 2012 19:11:14 -0700
    ...Clutch pedal goes only halfway > > Under normal operation the clutch pressure plate pushes the driven (slave), > cylinder back in when the pedal is released...