Skip to main content
Gerry | Vanagon
Checking account...
← vanagon.com home · Continue the discussion in the forum

Search messages and discussions

Clear search

Search preserved mailing-list messages and current email and website contributions. Current posts are searchable before weekly archival. Recovery gaps remain possible. Words are matched together; try fewer terms if needed.

Page 6+: 60 results shown for Crankshaft oil seal.

Source-balanced relevance: matches from both collections are interleaved, with source dates breaking ties. Restoration time is not the original posting date.

  • Rebuild time
    Historical mailing list - Bob O'Shaughnessy
    Sun, 1 Dec 96 08:08:59 -0500
    ...crankshaft measuring, but is there anything out of the ordinary? Third, heads. I am thinking of at least getting valve guides and seals, but...
  • Re: Bottom end reassembly?
    Historical mailing list - Bulley
    Mon, 24 Apr 2000 17:40:07 -0400
    ...crankshaft bearings and place the cam and crank in place (proper timing alignment observed with marks on gears). #3 Apply thin bead of seal...
  • Re: '86 Vanagon removing/installing flex plate & torque converter
    Historical mailing list - Scott Daniel - Turbovans
    Sat, 20 Apr 2013 22:03:24 -0700
    ...Besides being 'in there for sure and won't loosen up' ..those threads also need to be sealed against engine oil going past the...
  • Re: Advice on an Oil-pump oily gasket slow leak
    Historical mailing list - David Devere
    Sun, 30 Jun 2002 12:21:55 -0500
    ...seam to come from the > oil pump gasket, I am sure of that! (not from the rear seal crankshaft for > sure). As my engine...
  • Re: Shifter Problem
    Historical mailing list - Paul Connelly
    Thu, 14 May 2009 16:52:31 -0600
    ...In my case, someone I knew >>>>>> made one for me. >>>>>> >>>>>> Item 4) the slipping clutch was precipitated by the oil from the >>>>>> crankshaft seal...
  • Re: 81 Westy Dead Engine - Long
    Historical mailing list - Stan Wilder
    Mon, 16 Sep 2002 00:11:03 -0500
    ...shaft pilot needle bearing in the end of the crankshaft. Replace the felt seal and *O* ring in your flywheel. Don't trust new...
  • Re: Overfilling the oil issues
    Historical mailing list - Scott Daniel - Turbovans
    Sun, 22 May 2011 16:41:58 -0700
    ...If >> really >> overfilled and kept at high speed long enough the next vent is the >> crankshaft seals. Also the extra oil makes for a...
  • Re: Piston Ring Replacement
    Historical mailing list - Kenneth Wilford
    Mon, 14 May 2007 11:40:17 +0000
    ...I use either Marvel Mystery Oil or Automatic Transmission fluid as my cutting oil for honing. Pour it into the cylinder every so often...
  • Re: Rebuild longevity
    Historical mailing list - Stuart
    Sun, 12 Sep 1999 18:11:03 -0700
    ...and resized rods > > Reground (not just polished) crankshaft > > New oil pump > > OEM gasket set with OEM sealant > > All corroded case studs replaced (probably most...
  • Re: 1985 Vanagon GL
    Historical mailing list - Marion Lathem
    Sat, 19 Aug 2006 05:42:28 -0500
    ...When I had the crankcase apart, I just know there was no oil seal by the oil slinger ring. Course the VW engines were...
  • Oil Level Issue and Comment
    Historical mailing list - Frank Grunthaner
    Wed, 27 Jun 2001 22:36:26 EDT
    ...In addition, the gear type oil pump can lose pump pressure because of the breakup of the side wall seal (gear-to-gear and...
  • Re: Boston Bob Flywheel Install - OMG
    Historical mailing list - Scott Daniel - Turbovans
    Fri, 25 Jun 2010 21:08:44 -0700
    ...the only thing I would add to that video is to dampen or soak the felt seal in oil .. think I read that somewhere...
  • New lister & first time owner of '87 Vanagon GL
    Historical mailing list - Douglas and Annie Dodson-M�uck
    Sat, 8 Aug 2009 02:32:16 -0500
    ...pulse when rotor heats up, minor oil leak w/ possible origin between block & water-pump (crankshaft seal perhaps?). It starts right away,runs pretty...
  • Re: Hi list. 90 syncro bad leak stuck in parking lot
    Historical mailing list - Dennis Haynes
    Sat, 28 Jun 2014 17:54:44 -0400
    ...John On 6/28/2014 2:41 PM, Nomadix wrote: > Hi just wanted to post an update. > > Mainshaft seal bad > Clutch disc had oil...
  • GEX Rebuilt Engines
    Historical mailing list - Ken Korn
    Thu, 12 Nov 1998 21:13:12 -0600
    ...The oil pump was not the VW heavy duty bus pump and had been sealed up with JB Weld or similar. The Vanagon (and...
  • Re: Overfilling the oil issues
    Historical mailing list - Marius Strom
    Tue, 24 May 2011 18:09:44 +0000
    ...If really overfilled and kept at high speed long >>> enough the next vent is the crankshaft seals. Also the extra oil >>> makes for a...
  • Re: 80 Westy Engine Fire - Mystery Solved
    Historical mailing list - Stan Wilder
    Sun, 11 May 2003 08:20:59 -0700
    ...I cite a few examples: #1) I found a wrist pin retaining criclip in my oil pan when I changed the oil after initial...
  • Re: Cooling system hose diagram
    Historical mailing list - David Beierl
    Sun, 21 Apr 2013 19:58:32 -0400
    ...I have removed the rear crankshaft seal behind >the flywheel. I has a very thin sort of metal ring that must >space the original...
  • Re: '86 Vanagon removing/installing flex plate & torque converter
    Historical mailing list - Dennis Haynes
    Sun, 21 Apr 2013 01:22:31 -0400
    ...Besides being 'in there for sure and won't loosen up' ..those threads also need to be sealed against engine oil going past the...
  • Re: 1985 Vanagon GL
    Historical mailing list - Rod Smith
    Sat, 19 Aug 2006 19:33:32 -0400
    ...where > nobody else can either.! > > I believe they pulled the crankshaft pulley seal out, and torqued the > crap out of the bolt.. in excess...
  • Re: newbie questions
    Historical mailing list - Michael Snow
    Sat, 28 Dec 2002 14:52:52 -0800
    ...The crankshaft seals are relatively easy to replace by following the instructions in the Bentley. Unfortunately, you have to remove the timing components from...
  • Re: Overfilling the oil issues
    Historical mailing list - Robert Stewart
    Tue, 24 May 2011 19:13:34 -0400
    ...If >>>>> really >>>>> overfilled and kept at high speed long enough the next vent is the >>>>> crankshaft seals. Also the extra oil makes for a...
  • Volkswagen tool list for 1963-1967.(long)
    Historical mailing list - Eric Oster
    Thu, 16 Feb 1995 16:10:12 -0800 (PST)
    ...VW 210 Oil pump extractor VW 203b Crankshaft pulley extractor VW 203d Thrust pad for crankshaft pulley VW 204b Crankshaft oil seal installing tool...
  • DIESEL VANAGON QUESTIONS
    Historical mailing list
    Sat, 1 Apr 95 21:16:32 EST
    ...front brake rotors at 70,000 miles and clutch at 108,000 miles (plus crankshaft seals). it is our tertiary transportaion now, we kind...
  • Re: Engine rebuild - 2.1 L WBX
    Historical mailing list - SDF ( aka ;jim lahey' - Scott )
    Sat, 30 Aug 2014 20:22:58 -1000
    ...ah ha' for why it puked oil. didn't really find one ... but I did ... have the crankshaft mic'd and polished.. all new...
  • Re: Portland OR Vanagon Engine Swap Shop
    Historical mailing list - SDF ( aka ;jim lahey' - Scott )
    Mon, 17 Aug 2015 23:57:59 -1000
    ...Natureally you want a very high quality new Rear Main Oil seal too. also ...be aware that the lower engine mounting studs are different...
  • Re: Transmission Woes
    Historical mailing list - David Milo
    Sun, 6 Nov 2011 08:23:14 -0500
    ...built in > > rubber lip type seal. > > Some material needs to be removed, by a machinist, on the crankshaft side > > of > > the flywheel, just a...
  • Re: Hi list. 90 syncro bad leak stuck in parking lot
    Historical mailing list - Thomas Wilsher
    Sat, 28 Jun 2014 16:12:56 -0700
    ...pilot bearing that has a seal built in. > You can also drill out the shoulder in the crankshaft bore to let that > longer bearing...
  • Re: AAZ swap progress
    Historical mailing list - Scott Ohana
    Mon, 22 Jul 2013 18:33:05 -0700
    ...surfaced, lubing throttle pedal assembly and cable, oil >> pump, oil seals and gaskets,and dropped off crankshaft to have timing gear >> updated tdi style...
  • Re: Piston Ring Replacement
    Historical mailing list - Dennis Haynes
    Mon, 14 May 2007 09:50:37 -0400
    ...The three piece rings use some oil. I have also used the "gap less" rings by total seal. Expensive but they do almost eliminate...
  • Re: 1.9 Vanagon oil lite shananagons (cont.)
    Historical mailing list - Dennis Haynes
    Thu, 18 May 2006 18:37:24 -0400
    ...Every couple thousand miles, or so, I have Reggie change the oil and filter. Castrol SAE 30 oil, I believe, and one of those...
  • Re: For the Newbies - Vanagon secrets revealed
    Historical mailing list - Marion Lathem
    Tue, 29 Aug 2006 19:05:18 -0500
    ...Course I still have the problem of the over tightened crankshaft pulley bolt, and lack of an oil seal behind it. This winter I...
  • Clutch replacement report - longish
    Historical mailing list - Alistair Bell
    Fri, 16 Mar 2001 11:58:12 -0800
    ...This allowed me to drive the old mainshaft oil seal out from behind. I cleaned and lubed the release shaft, installed the new throw...
  • Re: Transmission Woes
    Historical mailing list - Scott Daniel - Turbovans
    Sat, 5 Nov 2011 23:24:25 -0700
    ...built in rubber lip type seal. Some material needs to be removed, by a machinist, on the crankshaft side of the flywheel, just a...
  • Re: Overfilling the oil issues
    Historical mailing list - Robert Stewart
    Tue, 24 May 2011 13:54:23 -0400
    ...If >>> really >>> overfilled and kept at high speed long enough the next vent is the >>> crankshaft seals. Also the extra oil makes for a...
  • Re: Ever just repair one head? What happened?
    Historical mailing list - Benny boy
    Wed, 23 Mar 2005 10:53:06 -0500
    ...crankshaft and everything around + some shaky engine reaction. So before, you should take a few things in consideration; heads/engine age and compression, oil...
  • Re: Overfilling the oil issues
    Historical mailing list - Edward Maglott
    Tue, 24 May 2011 14:37:29 -0400
    ...If > >>> really > >>> overfilled and kept at high speed long enough the next vent is the > >>> crankshaft seals. Also the extra oil makes for a...
  • On the Subject of Turbo's, Oil Pans and Vanagons
    Historical mailing list - Frank Grunthaner
    Wed, 1 Aug 2001 13:49:08 EDT
    ...crankshaft seal retaining bolt. At the rear of the engine, the max oil level just gets to the top of the oil pan seal...
  • VW Inline 4 motor 'revise and re-install' update, (long)
    Historical mailing list - Don Hanson
    Tue, 15 Jun 2010 09:28:32 -0700
    ...The 'new' 94 Jetta block (with it's supposedly better forged crankshaft and under piston oil-squirter system) is now sitting ready to go...
  • Re: Boston Bob? or GoWesty?
    Historical mailing list - ROBERT DONALDS
    Mon, 19 Jan 2004 20:16:05 -0500
    ...Other things I do with each engine is to make oil pressure' check for oil leaks and check compression before the engine is taken...
  • Fw: 2.1L Align bore and main bearings
    Historical mailing list - ROBERT DONALDS
    Wed, 3 Dec 2003 21:18:30 -0500
    ...2.1L Align bore and main bearings > Curt > the crankshaft can be ground .010ths or 020ths as needed I have cranks on > hand in...
  • VW Parts and equipment for sale (fwd)
    Historical mailing list - Jeffrey Olson
    Fri, 13 Dec 1996 12:23:22 -0800 (PST)
    ...681 Main drive shaft oil seal extractor Snap-on tools S5915 10 mm offset closed-end wrench S9094B Seal puller Others 17 mm Allen...
  • Re: Timing Chains, Belts, Gears, etc (NVC)
    Historical mailing list - Benny boy
    Sun, 24 Jun 2007 09:50:25 -0400
    ...why modern engine use thinner oil, the space between the crankshaft and bearing is so tight that thick oil would no pass. Why not...
  • FS: 1984 Vanagon Westfalia with "going - gone" Engine (Long)
    Historical mailing list - Leaf
    Thu, 20 Feb 2003 08:27:46 -0800
    ...Regular oil changes () New O2 sensor, timing adjust and plugs ($118) Replace fuel hoses, seals and gaskets ($235) From Bus Depot ($360) -Complete new...
  • VW parts for sale
    Historical mailing list - Roger Lippman
    Mon, 5 Feb 1996 21:08:09 GMT
    ...40 HP-1600 Brazil 113 105 245F 1 Front main engine oil seal 40 HP-1600 113 105 401A 4 Conn. rods 40 HP...
  • Re: Piston Ring Replacement
    Historical mailing list - Zoran Mladen
    Mon, 14 May 2007 08:04:35 -0700
    ...I use either Marvel Mystery Oil or Automatic Transmission fluid as my cutting oil for honing. Pour it into the cylinder every so often...
  • Re: '87 Vanagon GL: Oil leaks
    Historical mailing list - Jim Felder
    Wed, 19 Aug 2009 22:22:13 -0500
    ...whom I purchased it said that he thought one of the >> >> crankshaft seals could be the culprit. �The leaks do appear to dripping >> >> from...
  • VW Parts For Sale
    Historical mailing list - Roger Lippman
    Wed, 13 Mar 1996 01:13:21 GMT
    ...40 HP-1600 Brazil 113 105 245F 1 Front main engine oil seal 40 HP-1600 113 105 401A 4 Conn. rods 40 HP...
  • VW parts for sale
    Historical mailing list - Roger Lippman
    Tue, 26 Mar 1996 21:47:59 GMT
    ...40 HP-1600 Brazil 113 105 245F 1 Front main engine oil seal 40 HP-1600 113 105 401A 4 Conn. rods 40 HP...
  • Re: Vanagon Head Leaking Around The Head Nut(S)
    Historical mailing list - Mike B
    Tue, 15 Apr 2014 04:16:54 -0400
    ...a crankshaft run-out check to > determine wear condition of the crankshaft and main bearings. If good - > or within limits - and oil pressure history...
  • Re: New lister & first time owner of '87 Vanagon GL
    Historical mailing list - Roger Whittaker
    Sat, 8 Aug 2009 10:55:07 -0700
    ...pulse > when rotor heats up, minor oil leak w/ possible origin between block & > water-pump (crankshaft seal perhaps?). It starts right away,runs pretty...
  • Re: I want to kill my control arm bushings...
    Historical mailing list - Stan Wilder
    Sun, 27 Jul 2003 17:09:03 -0700
    ...identical in every way. (Strainer gasket sets, Oil filters, Gaskets and Seals, Crankshafts, Push rods, Lifters, Oil Pumps.) Stan Wilder On Sun, 27 Jul...
  • Re: Transmission Woes
    Historical mailing list - craig cowan
    Sun, 6 Nov 2011 07:41:55 -0500
    ...built in > rubber lip type seal. > Some material needs to be removed, by a machinist, on the crankshaft side > of > the flywheel, just a...
  • Re: AAZ swap progress
    Historical mailing list - ralph meyermann
    Mon, 22 Jul 2013 20:00:20 -0600
    ...surfaced, lubing throttle pedal assembly and cable, oil > pump, oil seals and gaskets,and dropped off crankshaft to have timing gear > updated tdi style...
  • Re: EXPERTISE NEEDED! oil pressure woes con't. part 4
    Historical mailing list - Brian Cochran
    Fri, 9 Feb 2001 11:18:15 -0800
    ...You didn't address why the oil pressure came back up to normal at slower speeds. Yesterday I put 35 miles on it (two...
  • Re: Flywheel Install / O - ring
    Historical mailing list - Scott Daniel - Turbovans
    Mon, 16 Apr 2012 14:31:37 -0700
    ...All seals on turning shafts need to be >> pre-lubed after all. >> and I always do that, soak it in oil, and it works...
  • Factory Tools List Vanagon
    Historical mailing list
    Wed, 15 Feb 1995 12:42:22 -0500
    ...the three groove crankshaft pulley Engine 3159, 116, ream piston for removal; multiple operatins Engine 3162, 16, crankshaft oil seals installing; this tool is...
  • Re: Transmission Woes
    Historical mailing list - pickle vanagon
    Sun, 6 Nov 2011 08:26:43 -0500
    ...built in > > rubber lip type seal. > > Some material needs to be removed, by a machinist, on the crankshaft side > > of > > the flywheel, just a...
  • Re: Fixing Vanagon Air Conditioning....trying at least
    Historical mailing list - Richard Koerner
    Sat, 10 Aug 2019 01:11:04 +0000
    ...With regular use and adequate oil in the system the oil will help keep the stuff inside. Small leaks in the condenser, compressor seal...
  • Re: New lister & first time owner of '87 Vanagon GL
    Historical mailing list - Ken Wilford
    Sat, 8 Aug 2009 08:44:43 -0400
    ...pulse when rotor heats up, minor oil leak w/ possible origin between block & water-pump (crankshaft seal perhaps?). It starts right away,runs pretty...