

| Subject: | Re: Follow-up odd noise on new gowesty engine |
| From: | Alistair Bell |
| Date: | Tue, 31 May 2011 18:18:30 -0700 |
I had similar noise on my syncro after I bashed that transverse pipe that runs under the muffler. It was hitting the muffler brackets under certain conditions (engine load at mid rpm) and drove me nuts tracking it down. I fiddled with the muffler brackets and pried the (slightly bent) pipe away to fix it. alistair On 31-May-11, at 5:11 PM, John Goubeaux wrote: > I too suspected the rear engine mounts, however I replaced them with > the > new engine. I also got an opinion from another mechanic who indicated > that everything looked like it was in order. Also, because I had > another > bad pipe and and a poorly cast collector knuckle ( all same > aftermarket > brand) I had to return I suspected the pipe bend. Maybe the new engine > mounts are thicker, this would account for the rear engine mount bar > being closer I think ? They did look a lot beefier than the old ones > they replaced ? > > -john > > On 5/31/2011 4:52 PM, Jake de Villiers wrote: >> John, I have had the Danish exhaust pipes on both my 1.9 and 2.1 with >> no issues at all, so I'd tend to look for worn or broken engine and/ >> or >> transaxle mounts. >> >> Jake >> >> On Tue, May 31, 2011 at 3:35 PM, John Goubeaux <john@ucsb.edu >> <mailto:john@ucsb.edu>> wrote: >> >> So , just to follow up on this thread I determined that the >> "clunk" >> noise I ( sometimes) hear when starting or stopping the engine >> is the >> rear exhaust header hitting the rear engine mount bar. I >> replaced the >> exhaust headers on the new engine (after marker Danish ones) and >> along >> with poor quality issues ( one of them had a cracked weld at the >> flange) >> it looks like the bend on the rear pipe comes too close to the >> rear >> engine mount allowing it to hit the mount bar. Not sure if I can >> get a >> muffler guy to fix this or not but at least i know what is >> causing it. >> >> I'm surprised no one else has had this problem as well, as I >> suspect a >> lot of people are using the aftermarket pipes being sold. These >> were >> purchased from Van Cafe. >> >> -john >> >> Guys, >> >> I have roughly 500 + miles on a new GoWesty 2.2 engine that >> I just >> installed and am curious about an odd noise it makes, but only >> when it >> is warm, eg been brought up to temp. On startup, ie >> cranking, just >> before it starts and when turning of the engine there is a >> small clunk >> noise. Almost as if before and after ignition takes place a >> compression >> sound as the engine comes to a stop. The engine runs fine and >> there are >> no odd noises while running only at start and stop. I have not >> been able >> to listen to it back at the engine compartment yet but am >> planning to do >> so. Nothing is loose that can explain this and maybe it is a >> normal >> sound and is compression on these engines? Oddly it only >> exhibits this >> noise when hot though. Could it be a loose head? Sticking >> valve? >> >> Logically I am being very careful to break it in properly >> and am >> listening and watching its behavior carefully and want to >> ensure that >> this is not something that is going to end up being an issue >> down the >> road. >> >> Any ideas ? >> >> -john >> >> >> >> >> -- >> Jake >> >> 1984 Vanagon GL 1.9 WBX - 'The Grey Van' >> 1986 Westy Weekender/2.5 SOHC Subie - 'Dixie' >> >> Crescent Beach, BC >> >> www.thebassspa.com <http://www.thebassspa.com> >> www.crescentbeachguitar.com <http://www.crescentbeachguitar.com> >> http://subyjake.googlepages.com/mydixiedarlin%27 >>
Have something to add on this topic today? Revive this thread in the forum »