

| Subject: | Re: Re-introduction & Dash Removal Question |
| From: | JRodgers |
| Date: | Tue, 25 Feb 2014 16:34:29 -0600 |
TJ Hannick showed me that nearly all the switches can be taken apart, cleaned, and reassembled nearly good as new. I was surprised because my switch experience was if it breaks, buy a new one.. He said not necessary. John On 2/25/2014 3:16 PM, Larry Alofs wrote: > I have been on this list for at least 10 years and this is the first I have > heard about relocating the power window switches. I am not sure why > someone would want to do this unless it is to make use of some replacement > switches that would not fit in the doors. > > When the original switches no longer make contact reliably, it is > possible to pop them open and clean and polish the contacts. It is rather > difficult, however, to keep the small parts in place while you pop them > back together. If a switch doesn't feel like it is clicking properly, it > just doesn't "push", it's because the little rocking contact in there has > jumped out of place. > > Jettas of the same vintage with power windows have a nearly identical > which can be used in a vanagon. The wires from your original switch will > need to be soldered on tho, because the plug that the Jettas use projects > too far into the door and gets hit by the window when it comes down. BTDT > :-) Of course Jetta switches from a junkyard may also be worn out. > Bring an ohmmeter. > > Recently when I needed a switch for an '87 Wolfsburg I am working on, I > could not seem to repair any of the old ones I had. I thought that someone > on the subaruvanagon list had once mentioned using Subaru switches so I got > one out of the junk '91 Legacy that had donated the current engine for my > '91 GL. After a lot of Bentley study and quality time with a continuity > tester, I found that the Subie switch was the same electrically as the > Vanagon one. After some soldering, Dremel carving, and J B welding it is > now fastened to the bezel (eustachian?) in the passenger door and works > fine. What fun. > > Larry A. > > > > On Tue, Feb 25, 2014 at 2:41 PM, Nathan Wood <dart330@gmail.com> wrote: > >> Thank you to everyone for all the helpful suggestions. This is really >> turning into a big project. Added to my list below I now also have this to >> do: >> >> Headlight Relays >> Box flap seals and body gasket >> Sound-deadening material >> Fix any seam rust (not sure the best way to go about this, POR-15?) >> Tighten 12v outlet (mine is loose) >> Check wiper shafts >> Washer jet tubes >> Lube brake pedal & control cables >> Check ground star block (if rusted, replacement available from?) >> Relocate power window switches (GoWesty has a kit. Not sure if I want to >> do this or not. Do most people ditch the factory switches? My drivers side >> is inoperable but I haven't diagnosed it yet.) >> Have wife ready to help lift dash off. >> >> I might have to wait a little while to get started so I can source all the >> parts and make sure the weather will be warm enough and tornado free as I >> imagine this will take me 2-3 weekends to complete. >> >> Nathan >> >> On 02/23/14, Nathan Wood<dart330@GMAIL.COM> wrote: >> >> Hello list, >> >> I have been away from the Vanagon community for some time. I joined back in >> 2001 when I picked up an 85 Westy. Since then I also had an 87 Syncro and >> an 82 Westy all of which I had to sell due to 2 job relocations. >> >> Things have settled down and I recently picked up a 90 Carat Automatic for >> a project vehicle. I believe I am the 3rd owner. The last one purchased it >> in 1998 and only drove it 7k miles in 14 years. It is pretty much bone >> stock with 125k miles, even has the factory radio. My plan is to simply fix >> all the little broken stuff and do as much preventative maintenance as >> possible so we can take it camping and hit the VW shows. This is my first >> automatic, so that in itself is a bit of a new adventure. >> >> So far I have done the tires (proper Hankooks), shocks (Bilstein HD), rear >> hatch struts, and am fixing all the various lights that aren't working due >> to burnt out bulbs or rusted out housings. I have it at the local shop >> right now getting the ATF & diff fluids changed along with the Foreign Auto >> Supply transmission cooler being installed. >> >> The next big thing for me to tackle is the dash removal as the front blower >> fan is inoperable. This is a first for me, as I never had this problem on >> my previous Vanagons. I have read through the step-by-step on Ben's website >> and I don't think I will have too much trouble. >> >> My question is what is the exhaustive list of things that need to be >> replaced while the dash is out? So far I have: >> >> Blower Fan >> Heater Core >> Heater Core Valve >> Heater Box Clips >> Ignition Switch >> Brake Master Cylinder (no clutch MC since it is an auto) >> Wiper Motor >> >> Is there anything else I should tackle if I plan to drive this for the next >> 5-10 years? I don't want to have to do this more than once. >> >> Thanks for the help! It is great to be driving a Vanagon once again. >> >> Nathan, >> Now in OKC. >> >
Have something to add on this topic today? Revive this thread in the forum »