Yes, this is my hope as well...either it helps, or I'm going to yank it
apart...sort of my last ditch before the search for a new engine or good
used....

Thanks all...

Dave

On Friday, August 5, 2016, Tyler Hardison <tyler@seraph-net.net> wrote:

> Nope! But I learned a lot while I was in there. :-D
>
> On Fri, Aug 5, 2016 at 11:39 AM, Stuart MacMillan <stuartmacm@gmail.com
> <javascript:;>>
> wrote:
>
> > Great, did it help?
> >
> >
> >
> > Stuart
> >
> >
> >
> > *From:* Tyler Hardison [mailto:tyler@seraph-net.net <javascript:;>]
> > *Sent:* Friday, August 05, 2016 11:36 AM
> > *To:* Stuart MacMillan
> > *Cc:* vanagon@gerry.vanagon.com <javascript:;>
> >
> > *Subject:* Re: 3149 Tool for Crank Pulley Removal - What was I thinking?
> >
> >
> >
> > Yes, I installed one in my 1.9 and it fit just fine.
> >
> >
> >
> > On Fri, Aug 5, 2016 at 11:35 AM, Stuart MacMillan <stuartmacm@gmail.com
> <javascript:;>>
> > wrote:
> >
> > Will a high volume pump fit behind the pulley?  As I recall, the pump is
> > bigger and sticks out farther.
> >
> > Stuart
> >
> >
> > -----Original Message-----
> > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com
> <javascript:;>] On Behalf
> > Of Tyler Hardison
> > Sent: Friday, August 05, 2016 10:50 AM
> > To: vanagon@GERRY.VANAGON.COM <javascript:;>
> > Subject: Re: 3149 Tool for Crank Pulley Removal - What was I thinking?
> >
> > Hi Dave,
> >
> > To remove the oil pump does NOT require removing the rear pulley. It will
> > clear the pully just fine. Just remove the cross-under coolant hose.
> >
> > On Fri, Aug 5, 2016 at 10:48 AM, Dennis Haynes <d23haynes57@hotmail.com
> <javascript:;>>
> > wrote:
> >
> > > A good impact wrench with proper socket will loosen that bolt. Mark it
> > > before removal so you can get it back where it was. There is also an o
> > > ring behind that pulley.
> > >
> > > Dennis,
> > > From my phone.
> > > ________________________________
> > > From: David<mailto:fjazzbass@GMAIL.COM <javascript:;>>
> > > Sent: ‎8/‎5/‎2016 10:42 AM
> > > To: vanagon@GERRY.VANAGON.COM <javascript:;><mailto:
> vanagon@GERRY.VANAGON.COM <javascript:;>>
> > > Subject: 3149 Tool for Crank Pulley Removal - What was I thinking?
> > >
> > > So I'm in the middle of the odyssey to remove the oil pump and to get
> > > to the thing I have to take off the crank pulley... Ha ha, Bentley
> > > joke...3149 tool?!
> > >
> > > Ha ha trying to use an impact on that 258 foot pound bolt...
> > >
> > > Ok guys...not trying to work harder, but smarter...and you all are my
> > > brains at the moment...
> > >
> > > What have you all used? I have tons of clearance because I've taken
> > > everything out of the way...
> > >
> > > Thanks!
> > >
> > > Dave
> > > 85 GL 1.9er...
> > >
> >
> >
> >
>