Hi Jeff,

I used Fat Matt,  I think that is the same product sold at Go Westie.  I got it on sale at amazon for a large amount a few years ago. I did large portions of the van.  I recently had to look inside a few panels and it is holding up just fine.

I like the sound deadening on the road and off.

When I ride in vans without it we need to talk very loudly to hear each other.  In my van it is much easier to hear with a normal voice even with passengers in the back. I also did areas more fully and also more areas then most would recommend.  I like being able to walk around my van and tap panels and hear a nice solid thunk.  The sliding door, the hatch, and the front doors sound so solid compared to before. 
even the nose sounds more solid even though I couldn’t reach everything.

I still need to do behind the cabinets and such but that will wait until I need to get in there for another reason.

I’m very happy with the result.  the material was easy to cut with a utility knife, no mess. forgiving If I made a error.  no smell. and lasting nicely.

Eric Caron 
85 GL Auto Westfalia 

> On Jun 29, 2017, at 8:47 PM, Jeff Palmer <w.jeff.palmer@icloud.com> wrote:
> 
> Hi Eric.  What material did you use to deaden the sound, and are you happy with it?
> 
> Thanks
> Jeff
> 
>> On Jun 29, 2017, at 6:17 PM, Eric Caron <ecaron1@COMCAST.NET> wrote:
>> 
>> And,how about adding some sound deadening material while it is easy to cover the front.  Should make a nice difference with road, wind, and rain sounds.  I reached a bit over half of mine and it is a nice improvement .  I’ll do the rest if the dash or when the dash comes out.
>> 
>> Eric Caron 
>> 85 GL Auto Westfalia 
>> 
>> 
>>> On Jun 29, 2017, at 5:40 PM, Jaime Forero <jforero@SBCGLOBAL.NET> wrote:
>>> 
>>> You might:
>>> See if heater motor needs replacement. You might take the heater assembly out and clean the heater core. 
>>> See if heater and vent controls need adjusting or cables replaced
>>> See if radio antenna needs replacing. Routing the cable‎ is easy with dash out.
>>> See vacuum booster is OK as well as lines to it
>>> See if master cylinder is leaking as well as the clutch master cylinder.
>>> See about cleaning the common ground plug.
>>> 
>>> General cleaning.
>>> 
>>> Cheers
>>> Jaime
>>> 
>>> Sent from my BlackBerry 10 smartphone.
>>> Original Message  
>>> From: J.C.
>>> Sent: Thursday, June 29, 2017 12:15 PM
>>> To: vanagon@GERRY.VANAGON.COM
>>> Reply To: J.C.
>>> Subject: Any repair recommendations while dashboard is removed?
>>> 
>>> Following up on my "brake pedal not retracting' question from a while
>>> ago, we finally got her into the shop and the diagnosis is that it's
>>> the brake booster (thanks for the pointer Ken!)
>>> 
>>> My new question for the list is as to what repair/replacements we
>>> might want to do while the dash is completely out. Would love to save
>>> on duplicate labor costs if we can.
>>> 
>>> This is for an 85 Westy.
>>> 
>>> Thanks!
>>> 
>>> 
>>> On Wed, May 17, 2017 at 1:27 AM, kenneth wilford (Van-Again)
>>> <kenwilfy@comcast.net> wrote:
>>>> Had this same problem on a VW Bus recently. It was the brake booster.
>>>> There is a spring inside that which allows the pedal to return. We have
>>>> them available on our site at www.vanagain.com if you need one.
>>>> 
>>>> Ken
>>>> 
>>>> 
>>>> On Wed, May 17, 2017, 2:22 AM J.C. <dougm+sfbayrangers@kzsu.stanford.edu>
>>>> wrote:
>>>>> 
>>>>> Question for the list, that I haven't found a definitive answer for:
>>>>> My girlfriend's 85 Westy has an issue wherein the brake pedal isn't
>>>>> retracting into the resting position. Thus, the brakes are dragging
>>>>> (and the temporary solution has been to use one's foot to retract the
>>>>> pedal while driving.) The brakes themselves don't feel mushy/soft,
>>>>> thus it doesn't seem to be a master cylinder issue, or air in the
>>>>> lines.
>>>>> 
>>>>> My 1st thought was that there was an issue with the spring, but (as
>>>>> well as I could tell) it doesn't appear to be broken, and it does
>>>>> appear to be attached.
>>>>> 
>>>>> Does anyone have an idea as to how to diagnose and repair?
>>>>> 
>>>>> (Searched the 1st 8 pages of results from a search of the archives but
>>>>> couldn't find anything.)
>>>>> 
>>>>> Thanks.
>