GoWesty does have those parts, but I don't know whether they would improve
matters for you.

On Fri, Sep 27, 2024 at 5:52 AM ddbjorkman@verizon.net <
ddbjorkman@verizon.net> wrote:

> Hi Dave.
>
> Thanks for the reply.  I mean the knob mechanism that holds the table*
> leg* in place.
>
> Dave B.
>
> On Thursday, September 26, 2024 at 10:36:03 AM EDT, David McNeely <
> davmcneely40@gmail.com> wrote:
>
>
>
> https://gowesty.com/products/mounting-plate-for-table-top?variant=41426711543973
>
> There are other table parts listed as well.  This is the one I meant.  But
> rereading, it sounds like you were looking for help with the post, not the
> plate.
>
>
> On Thu, Sep 26, 2024 at 3:21 AM ddbjorkman@verizon.net <
> ddbjorkman@verizon.net> wrote:
>
> Hello David.
>
> It is the knob that keeps it extended in the up (as in up and down
> direction) position and keeps it from swinging away from the wall.  Do you
> have a kink to the Go Westy part??
>
> Dave B.
>
> On Tuesday, September 24, 2024 at 11:50:47 AM EDT, David McNeely <
> davmcneely40@gmail.com> wrote:
>
>
> Are we talking about the knob where the screw bears against the table leg,
> or the knob that secures the table to lock it in place so that it is stable
> in a horizontal plane?  Either way, it sounds like the bore is stripped so
> that the knob does not tighten.  For the horizontal stability knob, there
> is a plate that can be replaced, and GoWesty sells them, or did.  McNeely
>
> On Tue, Sep 24, 2024 at 8:04 AM Jim Arnott <jrasite@eoni.com> wrote:
>
> > From the archives:
> >
> > From: "ddbjorkman@verizon.net" <ddbjorkman@VERIZON.NET>
> > Subject: Rear table knob
> > Date: September 21, 2024 at 9:22:34 AM PDT
> >
> >
> > Hello all.The Westy has been running quite well recently.  Even no
> > problems on our 8.8K mile trip around the country.  So the list hasn't
> > heard from mem, other than the occasional reply.  But now I have a
> > problem.  The rear table knob does not restrict movement of the table as
> it
> > should.  I tried using the (different design) knob from the front table,
> > and even purchased a new knob to no avail.  Screw it down tight as one
> can
> > and the table still swings freely.  I have looked into the top hole it
> goes
> > into with the table removed, so know there is something in there.
> > Anybody got any fixes for this problem?  I have bungie corded the table
> to
> > the hand strap for now, but it's a poor solution.
> > Dave B.The Boston one
> >
> >
> > > On Sep 24, 2024, at 7:27 AM, Jim Arnott <jrasite@EONI.COM> wrote:
> > >
> > > Saw the post. Don’t have an answer.
> > >
> > > Jim
> > >
> > >
> > >
> > >> On Sep 23, 2024, at 6:07 AM, ddbjorkman@verizon.net <
> > ddbjorkman@VERIZON.NET> wrote:
> > >>
> > >> I hope you all got my post on the rear table knob problem.
> > >> I am a bit surprised that no one has replied or run into this problem,
> > nor come up with a fix.
> > >> Any ideas??  It is kind of a PITA, and I could use some help.
> > >> Dave B.the Boston one
> >
>
>