Ihre Nachricht konnte nicht an die Empf�ngerIn zugestellt werden. Sie enth�lt
folgenden Formfehler:

      Message ID (MID) Formfehler od. doppelt

Zur Kontrolle oder Wiederverwendung noch einmal die Nachricht, wie sie hier
in der OLN angekommen ist.
------------------------ (elektronische Abrei�kante) -------------------------
EMP: udo@oln.comlink.apc.org
MID: "<39B6A63281E42A79
ABS: CARVER_JEFFREY@aphub.aerojetpd.com (Jeff Carver)
WAB: vanagon@lenti.med.umn.edu
BET: Starting From Engine Bay
EDA: 19961205151934W-6:00
U-To: Multiple recipients of list <vanagon@lenti.med.umn.edu>
ROT: lenti.med.umn.edu!vanagon
Antwort-An: CARVER_JEFFREY@aphub.aerojetpd.com
GATE: RFC1036/822 sonne.comlink.apc.org [UNIX/Connect v0.74b4MB06]
U-Received: from mhub1.tc.umn.edu ([128.101.131.51]) by mail.comlink.apc.org with smtp	(Smail3.1.29.1 #12) id m0vVfa8-000KgkC; Thu, 5 Dec 96 16:19 MET
U-Received: from halfdan.med.umn.edu by mhub1.tc.umn.edu; Thu, 5 Dec 96 09:19:40 -0600
U-Received: from  (localhost) by halfdan; Thu, 5 Dec 1996 09:19:34 -0600
U-Return-Path: <vanagon@lenti.med.umn.edu>
U-Errors-To: gsker@lenti.med.umn.edu
U-Originator: vanagon@lenti.med.umn.edu
U-Precedence: none
U-X-Listprocessor-Version: 6.0c -- ListProcessor by Anastasios Kotsikonas
LEN: 1934

I recently hard wired in a remote start switch to my engine bay.  
Along with that I added a hot wire lead from the starter main lead.
There were lots of warnings about NOT using the terminal 15 coil lead 
for supplying power for timing lights, etc with the Hall distribution 
system, so I needed another hot source.

So with some perusing of the wiring diagram, and the addition of a 
male spade fitting to terminal 15 on the coil, I can now power up and 
start my engine from the engine bay itself without using a key!

The wiring diagram indicated that no running stuff would be affected 
by appllying power TO the coil's terminal 15, just dash stuff.

Alright, how likely is it that someone will reach up into a Vanagon 
engine through the license plate and figure this all out have a 
jumper handy, and WANT to steal a Vanagon?  You rear hatchers 
may have more concerns, such as a locking hatch.

I run a jumper (female connector to the coil, alligator to the hot 
lead) and hit the start switch, vroom!  The engine comes to life.  
Pulling the alligator stops it.  No more running around to kill the 
engine, no more listening from a distance when starting.
(BTW, don't wire it the other way around with the alligator at the 
coil, when you pull it to shut off engine, the alligator is still hot!, BTDT)

Another benefit for diagnostics is that I can check the engine 
electronics separate from the dash by disconnecting the wire from the 
ignition switch to the coil (at the dash, careful, it's hot when 
engine running)

Disadvantage is that none of the dash warning lights function as 
power is supplied by another piece of the ignition switch.

I had forgotten to post this until reading about Craig's dead '74.  
Modifying wiring like mine would allow Craig to diagnose dash 
separate from engine wiring. (Clara, are you lurking?)

Any downsides to this I missed

- Jeff
'80 Westi